Results 291 to 300 of about 935,449 (339)
Some of the next articles are maybe not open access.
Accuracy of three-dimensional measurements using cone-beam CT
Dentomaxillofacial Radiology, 2006Lesions causing intraosseous defects in the head and neck region are difficult to diagnose using two-dimensional radiography, and three-dimensional (3D) data provided by CT is useful but often difficult to obtain. Recently, cone-beam CT (CBCT) was made available, with the potential to become a practical tool in dentistry.
H M, Pinsky +4 more
openaire +2 more sources
Increasing the accuracy of imaging-based dimensional measurements
Optics and Photonics for Advanced Dimensional Metrology, 2020More than 95% of industrial inspection systems still rely on pure 2D information. Different measurement tasks like defect detection, micro-structure characterization, spectral characterization and dimensional metrology are typical application scenarios where standard 2D image processing based measurement systems are used.
Tobias Haist +2 more
openaire +1 more source
The accuracy of measurements of three-dimensional computed tomography reconstructions
Journal of Oral and Maxillofacial Surgery, 1996The purpose of this study was to evaluate the accuracy and reproducibility of linear measurements obtained from three-dimensional reconstructions of computed tomography (CT) scans.Ten rectangular acrylic blocks were prepared with titanium molybdenum alloy (TMA) markers spaced from 1 to 10 mm, respectively.
S W, Covino +3 more
openaire +3 more sources
Measuring Accuracy of Three-Dimensional Displacements in Holographic Interferometry
Applied Optics, 1973In order to establish a quantitative method of measuring the distribution of three-dimensional displacements by holographic interferometry, measuring errors caused by the following two factors are analyzed quantitatively: (i) reading error of fringe order, (ii) setting error of observing and illuminating directions.
T, Matsumoto, K, Iwata, R, Nagata
openaire +2 more sources
High accuracy three-dimensional attitude angle measuring device
Optics and Precision Engineering, 2016A high accuracy measuring device and corresponding measuring method for three;dimensional attitude angles (yaw, pitch and roll) were designed based on an autocollimator and a coordinate rotary transfer matrix. The working principle and structural composition were introduced.
孙国燕 SUN Guo-yan +4 more
openaire +1 more source
The accuracy of dimensional measurement in ultrasonic real-time scanning
The British Journal of Radiology, 1981The ease of examination with real-time ultrasonic scanners, together with the provision of calipers, combine to make dimensional measurement of anatomical or pathological features an attractive index, that should ideally be independent of the operator.
R C, Chivers, R A, Bacon, T J, Bloomberg
openaire +2 more sources
Dual-frequency fringe for improving measurement accuracy of three-dimensional shape measurement
Chinese Optics Letters, 2021A new phase unwrapping method based on dual-frequency fringe is proposed to improve both high accuracy and large measurement range of three-dimensional shape measurement by synthesizing the projected dual-frequency fringes obtaining higher and lower frequencies.
Zixiao Miao, Qican Zhang
openaire +1 more source
Accuracy in integrated circuit dimensional measurements
SPIE Proceedings, 1994The measurement of critical dimensions of features on integrated circuits and photomasks is modeled as the comparison of the images of the test object and of a standard object in a measuring device. A length measuring instrument is then a comparator. The calibration of the standard and the conditions necessary for a valid comparison are discussed.
openaire +1 more source
Accuracy and traceability in dimensional measurements
SPIE Proceedings, 1998While the importance of the concepts of measurement accuracy and measurement traceability has long been recognized, they have not always been applied in a consistent or rigorous manner. In 1993 the International Organization for Standards (ISO) published two documents which establish consistent definitions of these and other metrology terms and provide
openaire +1 more source
In-process dimensional measurement and control of workpiece accuracy
International Journal of Machine Tools and Manufacture, 1997Abstract This paper surveys the available technology for “in-process control” of machined products, particularly in relation to turning, and cylindrical grinding, prior to completion of the machining process. The techniques developed for controlling accuracy of the workpiece, whilst in situ , are described using representative examples of current ...
T. Yandayan, M. Burdekin
openaire +1 more source