Results 101 to 110 of about 365,900 (337)
Applied Sciences, 2019 In the present study, the effect of harsh conditions on the tensile behavior of lap-spliced carbon fiber textile-reinforced mortar (TRM) with different surface treatment methods was investigated through the direct tensile test.
Hai Van Tran +2 more
doaj +1 more source
A technique for the measurement of reinforcement fibre tensile strength at sub-millimetre gauge lengths [PDF]
, 2001 The strength of composite reinforcement fibres is normally measured on samples of much greater length than the actual residual fibre lengths found in many composite materials.
Kalinka, G., Thomason, J.L.
core +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
Experimental study and verification on tensile strength of remolded clay
Shuiwen dizhi gongcheng dizhiThe tensile strength of clay is an important factor in determining the stability of soil slope. Due to the fragmentation of soil, the understanding of the tensile strength of clay is not clear. In this study, the uniaxial tensile test of remolded clay is
Shuaixin BAI +5 more
doaj +1 more source
The mechanical properties of anisotropic polymers [PDF]
, 1966 The work in this period can conveniently be split into two parts which are reported separately. Part I is concerned with experimental work on the stress-strain properties of anisotropic polythene.
Darlington, M.
core
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
Development and performance evaluation of sustainable lightweight geopolymer based fireproofing coatings for steel construction [PDF]
Sustainable StructuresThis study developed a novel, sustainable, lightweight, and high-ductility fireproofing coating using granulated blast furnace slag (GBFS), fly ash microspheres (FAC), alkali activator, and polyethylene (PE) fiber as raw materials.
Zhenyu Huang +2 more
doaj +1 more source
Microstructure and mechanical properties of as-built and heat-treated electron beam melted Ti–6Al–4V [PDF]
, 2019 This paper investigates the effect of post-deposition heat treatment on porosity, microstructure, and mechanical properties of Ti–6Al–4V produced via an Electron Beam Melting process. Samples were studied in the conditions of as-built and heat treated at
Abdul Khadar Syed +4 more
core +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source