Results 51 to 60 of about 200,425 (299)
Journal of Rock Mechanics and Geotechnical Engineering, 2017 Tensile strength is an important material property for rocks. In applications where rocks are subjected to dynamic loads, the dynamic tensile strength is the controlling parameter.
Kaiwen Xia, Wei Yao, Bangbiao Wu
doaj +1 more source
Journal of Rock Mechanics and Geotechnical Engineering, 2022 The stress state in a rock mass is complex. Stress redistribution around underground excavation may lead to various failure modes, including compressive-shear, tensile-shear, and tensile failures.
Shucai Li +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Durability and Smart Condition Assessment of Ultra-High Performance Concrete in Cold Climates [PDF]
, 2016 The goals of this study were to develop ecological ultra-high performance concrete (UHPC) with local materials and supplementary cementitious materials and to evaluate the long-term performance of UHPC in cold climates using effective mechanical test ...
Allena, Srinivas +2 more
core
Performance enhancement of nylon/Kevlar fiber composites through viscoelastically generated pre-stress [PDF]
, 2013 Kevlar-29 fibers have high strength and stiffness but nylon 6,6 fibers have greater ductility. Thus by commingling these fibers prior to molding in a resin, the resulting hybrid composite may be mechanically superior to the corresponding single fiber ...
Cao +26 more
core +1 more source
A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection
Advanced Engineering Materials, EarlyView.A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan +9 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
Mechanical performance of fibre reinforced concrete : the role of fibre distribution and orientation [PDF]
, 2014 Adding fibres to concrete provides several advantages, especially in terms of controlling the crack opening width after the cracking initiation of the composite. However, distribution and orientation of the fibres toward the crack plane are significantly
Abrishambaf, Amin +2 more
core
Nanocellulose as building block for novel materials [PDF]
, 2012 This thesis describes the fabrication of novel green materials using nanocellulose as the building block. Bacterial cellulose (BC) was used as the nanocellulose predominantly in this work. BC is highly crystalline pure cellulose with an inherent fibre
Lee, Koon-Yang, Lee, Koon-Yang
core +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source