Results 101 to 110 of about 208,274 (242)
Advanced Engineering Materials, EarlyView.Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente +3 more
wiley +1 more source
Cramer-Rao Bound for Sparse Signals Fitting the Low-Rank Model with Small Number of Parameters
, 2015 In this paper, we consider signals with a low-rank covariance matrix which reside in a low-dimensional subspace and can be written in terms of a finite (small) number of parameters. Although such signals do not necessarily have a sparse representation in
Shaghaghi, Mahdi, Vorobyov, Sergiy A.
core +1 more source
Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures
Advanced Engineering Materials, EarlyView.This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Direction-of-Arrival Estimation with Coarray ESPRIT for Coprime Array
Sensors, 2017 A coprime array is capable of achieving more degrees-of-freedom for direction-of-arrival (DOA) estimation than a uniform linear array when utilizing the same number of sensors.
Chengwei Zhou, Jinfang Zhou
doaj +1 more source
Advanced Engineering Materials, EarlyView.A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Direction of arrival estimation using combined coprime and nested array
Electronics Letters, 2019 A combined coprime and nested array geometry is designed and a corresponding direction of arrival (DOA) method is proposed. The proposed array has three subarrays, where two are prototype coprime subarrays, and both of them are nested to the third one ...
Jianfeng Li, Yunxiang Li, Xiaofei Zhang
doaj +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source