Results 241 to 250 of about 7,320 (303)

Numerical Simulation of Laser Cladding Using Cable Wires. [PDF]

Materials (Basel)
Liu W, Guo X, Jiang K, Liu J, Peng Z, Lu X, Zhang J, Cai Z, Wu D, Xu Y, Yan B.   +10 more
europepmc   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Transducers Across Scales and Frequencies: A System‐Level Framework for Multiphysics Integration and Co‐Design

Advanced Materials Technologies, EarlyView.
Transducers convert physical signals into electrical and optical representations, yet each mechanism is bounded by intrinsic trade‐offs across bandwidth, sensitivity, speed, and energy. This review maps transduction mechanisms across physical scale and frequency, showing how heterogeneous integration and multiphysics co‐design transform isolated ...
Aolei Xu, Mengyao Xiao, Zhouli Sui, Yinpeng Wang, Daoye Zheng, Yuxin Liu, Luwei Wang, Huajun Liu, Chengkuo Lee   +8 more
wiley   +1 more source

Microstructure Evolution and Solute Segregation of Inconel 718 in Laser Additive Manufacturing: A Numerical and Experimental Investigation. [PDF]

Materials (Basel)
Liu H, Xiao W, Yan B, Xiao H.
europepmc   +1 more source

Benchmarking Coaxial and Angular Optical Emission Spectroscopy With Recommendations for Reliable Compositional In Situ Monitoring During Laser Powder Bed Fusion

Advanced Materials Technologies, EarlyView.
ABSTRACT Real‐time insight into local chemistry is critical for reliable part quality in additive manufacturing, especially laser powder bed fusion (PBF‑LB/M), where rapid thermal cycles and localized evaporation can undermine part performance. Optical emission spectroscopy (OES) offers non‑intrusive, in situ plume monitoring, but detection geometry ...
Philipp Gabriel, Bastian Jülich, Anna Rosa Ziefuss, Florian Eibl, Stephan Barcikowski   +4 more
wiley   +1 more source

Effect of Heat Treatment on the Corrosion and Wear Behavior of Hastelloy C276 Alloy Fabricated via Laser Powder Bed Fusion. [PDF]

Materials (Basel)
Fang X, Wang Z, Ye C, Li Y, Zhang L, Yang J, Ye S, Shang X, Wang D, Liu D, Li S, Lu B.   +11 more
europepmc   +1 more source

Composition Driven Redistribution of Feeding Mechanisms in Hypoeutectic Al-Si-Mg Alloys. [PDF]

Materials (Basel)
Patarić A, Djurdjevic M, Manasijevic S, Stopic S, Mihailović M.   +4 more
europepmc   +1 more source

Comparison of Hybrid Enthalpy-Porosity Models in the Analysis of Solute Macro-Segregation in Binary Alloy Centrifugal Casting. [PDF]

Materials (Basel)
Seredyński M, Banaszek J.
europepmc   +1 more source

Deformation-Induced Formation of Stray Grains in Additive Manufacturing of Single Crystals. [PDF]

Adv Sci (Weinh)
Zhang D, Guo Z, Li Y, Wang L, Wu Y, Sun D, Yan W, Guo Y, Wang H, Liu W, Tao Y, Zhang B.   +11 more
europepmc   +1 more source