Results 131 to 140 of about 147,390 (303)

Human-carnivore conflict mitigation and lion population viability in Uganda’s Queen Elizabeth National Park

Frontiers in Conservation Science
The Uganda Carnivore Program (UCP), located in Queen Elizabeth National Park (QENP), has—among other large carnivore research and conservation measures—engaged in human-carnivore conflict mitigation and prevention efforts since 2015.
Michael W. Schwartz
doaj   +1 more source

Cracking the Code: Which Ocular Symptoms Predict Dry Eye Signs? Insights from a large international sicca registry

Arthritis Care &Research, Accepted Article.
Purpose The study aimed to identify symptom‐based predictors of dry eye disease (DED) signs in the Sjögrens International Collaborative Clinical Alliance (SICCA) cohort. Methods Retrospective analysis examining 16 ocular symptoms (most graded 0‐4) and artificial tear (AT) use (graded 0‐3) as predictors of DED signs [abnormal ocular surface staining ...
Pragnya R Donthineni, Chloe Shields, Rohit Muralidhar, Shreya Bhatt, Alan Baer, Robert Fox, Sara S. McCoy, Anat Galor   +7 more
wiley   +1 more source

Geopolitical conflict impedes climate change mitigation

npj Climate Action
There is ample debate and publication on climate change causing conflict. On the contrary, a Conflict=>Climate-nexus, i.e. the detrimental impact of conflict on mitigation has not been systematically charted anywhere.
Katharina Block, Mengyu Li, Jan Gärtner, Manfred Lenzen   +3 more
doaj   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Design and development of an off-normal warning system for SPARC

Nuclear Fusion
The SPARC tokamak is a compact, high-field, and high-current device that will rely on disruption mitigation and prevention strategies to address the risks associated with its high stored energy densities.
A.R. Saperstein, C. Rea, R. Sweeney, M.D. Boyer, G.L. Trevisan, Y. Wei, the MIT PSFC Disruptions Team   +6 more
doaj   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source