Results 21 to 30 of about 1,768 (186)
Ultrasonic welding of dissimilar materials: A review
Periodicals of Engineering and Natural Sciences (PEN), 2015 During the last few years ultrasonic welding has become significant attention regarding its suitable applications in comparison to traditional welding techniques. Bonding of dissimilar materials has always been a challenging task due to poor control on grain size and sensitive mechanical properties that could have been made by joining with traditional ...
Elma Kicukov, Ali Gursel
openaire +2 more sources
Micro-Study of Dissimilar Welded Materials
, 2014 {"references": ["Z. Jandric, M. Labudovic and R. Kovacevic, Effect of heat sink on\nmicrostructure of three-dimensional parts built by welding-based\ndeposition, International J. of Machine Tools and Manufacture, Vol. 44,\nIssues 7-8, June 2004, pp. 785-796. W.-K. Chen, Linear Networks and\nSystems (Book style). Belmont, CA: Wadsworth, 1993, pp.
E. M. Anawa, A. G. Olabi
openaire +2 more sources
Control of welding residual stress for dissimilar laser welded materials [PDF]
Journal of Materials Processing Technology, 2008 Abstract The most common problem of welding dissimilar metals (DMWs) with respect to residual stresses is the differences in the coefficient of thermal expansion and heat conductivity of the two welded metals. In the present work, a CO2 continuous laser welding process was successfully applied and optimized for joining a dissimilar AISI 316 stainless
Anawa, E., Olabi, Abdul-Ghani
openaire +3 more sources
Statistical analysis of second repair welding on dissimilar material using Taguchi method
Journal of Mechanical Engineering and Sciences, 2019 This paper presents an experimental investigation on effect of welding parameter to repair welding of dissimilar material using Gas Metal Arc Welding (GMAW) machine.
N. I. S. Hussein +3 more
doaj +1 more source
Mechanical and Microstructural Properties of Friction Stir Welded Dissimilar Aluminum Alloys and Pure Copper Joints [PDF]
MATEC Web of Conferences, 2019 Joining dissimilar metal alloys such as aluminum and copper is very difficult to be done because of alterations in chemical, metallurgical and physical behavior.
Winarto W., Anis M., Febryansyah B. Eka
doaj +1 more source
Experimental Review on Friction Stir Welding of Aluminium Alloys with Nanoparticles
Metals, 2021 To reduce environmental impacts and ensure competitiveness, the fabrication and construction sectors focus on minimizing energy and material usage, which leads to design requirements for complex structures by joining of similar and dissimilar materials ...
Cyril Vimalraj, Paul Kah
doaj +1 more source
High-pressure linear friction welding of dissimilar AA5052-H34 and AA6061-T6 joint
Journal of Materials Research and Technology, 2023 Dissimilar linear friction welding (LFW) of AA5052/AA6061 was performed at different applied pressures. A dissimilar joint obtained at a high applied pressure of 200 MPa exhibited a tensile strength equivalent to that of the AA5052 base material, mainly ...
Jeong-Won Choi +5 more
doaj +1 more source
Numerical Simulation of Laser Welding Dissimilar Low Carbon and Austenitic Steel Joint
Open Engineering, 2020 Numerical simulation of laser welding dissimilar joint was presented. Results of butt joint for low carbon and austenitic steels are studied. Numerical calculations based on thermo-mechanical method and phase transformation were used for estimating weld ...
Danielewski Hubert +4 more
doaj +1 more source
Nondestructive Testing of Welded Composite Metal Foams
Advanced Engineering Materials, EarlyView.X‐ray computed tomography (CT) is used to evaluate welded steel–steel composite metal foam (CMF) joints of two density classes. It reports variation in postweld spatial void distribution and correlates it to weld‐induced changes, mechanical performance, and failure within welded CMF panels.
Chinmaya Prerana Inguva +2 more
wiley +1 more source
Mağallaẗ Al-kūfaẗ Al-handasiyyaẗ, 2020 FSSW is a solid state joining method gained its significance as an alternate welding technique in the in electrical, electronic and automobile industries that used FSW welding.
Iman J. AlShaibani, Mohammed K. Aljanabi
doaj +1 more source