Results 151 to 160 of about 474,940 (289)
Elastic Properties and Thermal Expansion Behavior of a Polycrystalline VMnFeCoNi High‐Entropy Alloy
Advanced Engineering Materials, EarlyView.The high‐entropy alloy (HEA) V20Mn20Fe20Co20Ni20 (composition in at.%) can be made single‐phase face‐centered cubic (FCC) when annealed above 1338 K followed by water quenching. In this state, the alloy exhibits the greatest strength‐ductility combination of any quinary single‐phase FCC HEA.
Guillaume Laplanche +3 more
wiley +1 more source
Minimization of Welding Distortion in Large-Scale Welded Structures Using the MAG Method: Numerical and Physical Simulation of the Welding Process. [PDF]
Materials (Basel)Mróz M, Czech R, Pikuła J, Spólnik M.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath +2 more
wiley +1 more source
Adhesive Versus Spatial Anatomical Distortion Determines Energy Device Performance in Complex Total Laparoscopic Hysterectomy. [PDF]
J Obstet Gynaecol ResGüven CM, Özgür Ş, Uysal D.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley +1 more source
Advanced Engineering Materials, EarlyView.Residual adhesive after electrode loading in adhesive‐assisted resistance spot welding is quantified through a traceable experimental‐to‐digital workflow. Chromatic confocal topography provides calibrated surface‐height data, while OpenCV detects the electrode imprint and integrates adhesive height into comparable volume metrics.
Sung‐Min Wi, Jiangdong Zhao
wiley +1 more source
An Optimized Particle Swarm Algorithm for High-Precision Camera Calibration with Enhanced Wide-Angle Distortion Correction. [PDF]
Sensors (Basel)Ji Q +7 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt +5 more
wiley +1 more source
Training sample acquisition strategy based digital pre-distortion
, 2012 Digital pre-distortion (PD) is a promising technique for power amplifier (PA) linearization and efficiency enhancement. Parameter estimation for both PA and PD models are quite important in all pre-distortion schemes.
L Gui (13621342) +2 more
core
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source