Results 141 to 150 of about 18,472 (300)

Overview of heating and cooling. Perceptions, markets and regulatory frameworks for decarbonisation. Deliverable 3 - Overview of monetary and non-monetary incentives for the uptake of district heating and cooling and heat pumps

This Report covers Subtasks 3.1 to 3.4 of the project ‘Overview of Heating and Cooling: Perceptions, Markets and Regulatory Frameworks for Decarbonisation’ funded by the European Commission (EC).
Gilmore-Maurer, Mary, McKenna, Russell, Kachirayil, Febin, Muinzer, Thomas, Brandon, Elisabeth   +4 more
core   +1 more source

Optimization and assessment of solar-assisted cooling systems: A multicriteria framework and comparative study

Energy Conversion and Management: X
In the current context of global warming, where district cooling systems are increasingly burdening power grids worldwide, it is important to design and operate alternative systems that are not only environmentally friendly, but also cost effective for ...
Dana Alghool, Reem Khir, Mohamed Haouari
doaj   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Electrified Damage in Motion Systems

Advanced Engineering Materials, EarlyView.
The electrified damage in motion systems is a fundamental framework presenting the degradation pathway arising from the coupling of electrical energy transport with mechanical contact and interfacial chemistry. The framework positions electrified damage as a distinct degradation regime with unique characteristic surface morphologies and failures of ...
M. Humaun Kabir, Angelina Nguyen, Hong Liang   +2 more
wiley   +1 more source

Shallow burial of district heating pipes

, 2008
The aim with this paper was to study if the investment costs for district heating installations in suburban areas can be lowered with more rational construction work. A field trial was done with four twin pipes of dimension 2xDN32/160 laid between 600 mm
Forsaeus Nilsson, Stefan,, Sällberg, Sven-Erik   +1 more
core  

Composites of Shellac and Silver Nanowires as Flexible, Biobased, and Corrosion‐Resistant Transparent Conductive Electrodes

Advanced Functional Materials, EarlyView.
Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein, Tiago Carneiro Gomes, Eliza Ng, Simon Rondeau‐Gagné, Tricia Breen Carmichael   +4 more
wiley   +1 more source