Results 81 to 90 of about 2,389 (217)

Modeling Dislocation Cutting of γ′ Precipitates in Ni‐Base Superalloys: Linking Atomistic and Dislocation Dynamics Simulations

Advanced Engineering Materials, EarlyView.
Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé, Siwen Gao, Marc Fivel, Anxin Ma, Daria Smirnova, Sriram Anand, Arun Prakash, Julien Guénolé, Alexander Hartmaier, Erik Bitzek   +9 more
wiley   +1 more source

Operational research of adsorption chiller aggregate utilizing heat from district heating to produce chilled water for air conditioning

Eksploatacja i Niezawodnosc - Maintenance and Reliability, 2017
Emil Stańczyk, Bolesław Karwat, Ryszard Machnik, Jerzy Niedźwiedzki   +3 more
openaire   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Machine Learning‐Supported Analysis for Predicting and Visualizing Nonlinear Relationships Between Material Properties in Electroplated Chromium Layers

Advanced Engineering Materials, EarlyView.
This study applies machine learning regression to predict chromium layer thickness in decorative trivalent chromium electroplating, using 441 experiments from laboratory‐scale (1L) and pilot‐scale (14L) setups. Tree‐based models, particularly CatBoost, outperformed linear regression by capturing nonlinear parameter interactions (R2$R^2$ up to 0.77 ...
Christoph Baumer, Christopher Mai, Luca Eisentraut, Andreas Bund, Ricardo Buettner   +4 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

A Practical Noise2Noise Denoising Pipeline for High‐Throughput Raman Spectroscopy

Advanced Engineering Materials, EarlyView.
A lightweight and reproducible denoising pipeline for high‐throughput Raman spectroscopy is introduced, based on a 1D convolutional autoencoder trained with a Noise2Noise strategy. Using only repeated short‐exposure acquisitions, the method suppresses stochastic noise without reference spectra, enabling reliable spectral reconstruction while preserving
David Martin‐Calle, Cesar Alvarez‐Llamas, Vincent Motto‐Ros, Christophe Dujardin, Jérémie Margueritat, David Rodney   +5 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source