Results 121 to 130 of about 1,208,916 (313)
A Bibliometric Analysis of the Outdoor Thermal Environment Based on CiteSpace
BuildingsThe outdoor thermal environment (OTE) is closely related to sustainable urban development and human living, and related research has attracted widespread attention.
Chao Xie, Tangjun Feng, Li Hu
doaj +1 more source
Factors which influenced the reorganisation of a sub-district administration programme (an evaluation study of planning in Mataram City, Lombok, Indonesia) : a thesis completed and submitted in partial fulfilment of the requirements for the degree of Master of Resource and Environmental Planning (M.R.P.), Massey University, Palmerston North, New Zealand [PDF]
, 2007 Inequality between sub-district institutions as centres of public services within Mataram City area and the growth of Mataram city's population is projected to be an alarming problem to maintaining a continuous, good quality of public service.
Fikri, Muhamad Nazaruddin
core
Advanced Engineering Materials, EarlyView.Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller +8 more
wiley +1 more source
GIS as new tools and approach in state planning and monitoring: the experience of Negeri Sembilan, Malaysia [PDF]
, 2006 Malaysian planning methodology has changed over the years as emphasis has shifted from producing plan, which described a state of affairs expected of some future date, to one which acknowledged the continuous and cyclical nature of planning.
Idris, Ruaidah +3 more
core
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
Applied SciencesAiming to solve the challenges of the weak spatial and temporal correlation of medium- and long-term photovoltaic (PV) power data, as well as data redundancy and low forecasting efficiency brought about by long-time forecasting, this paper proposes a ...
Bin Wang +5 more
doaj +1 more source
Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam
Advanced Engineering Materials, EarlyView.Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley +1 more source
Advanced Engineering Materials, EarlyView.Cermets (60 vol.% AISI 316L stainless steel, 40 vol.% recycled MgO), intended for use in aluminum electrolysis, were pre‐oxidized in three furnaces with different heating technologies and subjected to a cryolite corrosion test. The different atmospheres influenced the formation of oxide layers, which in turn affected corrosion resistance and ...
Patricia Kaiser +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source