Results 291 to 300 of about 7,293,468 (349)

Disentangling the components of a multiconfigurational excited state in isolated chromophore with light-scanning-tunneling microscopy. [PDF]

Nat Commun
Ferreira RCC, Sagwal A, Doležal J, Neuman T, Švec M.   +4 more
europepmc   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

From Low-Loaded Mesophilic to High-Loaded Thermophilic Anaerobic Digestion: Changes in Reactor Performance and Microbiome. [PDF]

Microb Biotechnol
Modin O, Zheng D, Schnürer A, Lundwall T, Bolanos SE, Olsson J.   +5 more
europepmc   +1 more source

Influence of Temperature on Scratch and Wear Properties of Technical Thermoplastics: Implications for Material Selection

Advanced Engineering Materials, EarlyView.
The share of technical thermoplastics is expected to grow further in the e‐mobility segment. In this study, a detailed temperature‐based tribological characterization of technical thermoplastics is performed. The tribological properties are discussed in terms of the dynamic mechanical properties of polymers at different ambient temperatures. A proof of
Harsha Raghuram, Thomas Koch, Vasiliki-Maria Archodoulaki   +2 more
wiley   +1 more source

D2S-DiffGAN: a novel image classification model under limited labeled samples. [PDF]

Sci Rep
Li Y, Long W, Zhang L, Ren Y.
europepmc   +1 more source

X‐Ray Computed Tomography Quantifies Primary Phases and Reveals Crack Morphology in High‐Cycle Fatigue of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
Primary phases and a fatigue crack are studied in a forged blank of an aluminum alloy using synchrotron and laboratory X‐ray computed tomography. To image the crack, the fatigue test is interrupted, and a static tensile load is applied to open the crack.
Jakob Schröder, Ying Han, Tobias Fritsch, Bardia Hejazi, Alexander Ulbricht, Birgit Skrotzki, Giovanni Bruno   +6 more
wiley   +1 more source

Study on roof partition fracture based on dominant primary fracture. [PDF]

Sci Rep
Xia W, Qiang L, Yongkai Z, Yuqi R, Hao Y, Weijie W, Yuesong T.   +6 more
europepmc   +1 more source

Subgrain and Cavity Development during Creep of Al‐3.85%Mg

Advanced Engineering Materials, EarlyView.
Al‐3.85%Mg does form subgrains if crept at very high strains. This fact allows the unification of the creep description in two different alloys such as pure Al and Al–Mg alloys. It is classically considered that the creep mechanisms for type M (e.g., pure Al) and type A alloys (e.g., Al–Mg alloys) are different.
Augusta Isaac, Itziar Serrano‐Munoz, Aleksander Kostka, Martinus Putra Widjaja, Gaspar González‐Doncel, Giovanni Bruno, Ricardo Fernández   +6 more
wiley   +1 more source

Solving the Independent Domination Problem by the Quantum Approximate Optimization Algorithm. [PDF]

Entropy (Basel)
Pan H, Lu C.
europepmc   +1 more source

From Nature to Engineering: Mortar Volume and Interfacial Mechanics in Bioinspired Ceramics

Advanced Engineering Materials, EarlyView.
Inspired by natural armors like nacre, this study explores how varying the volume fraction of the soft mortar layer impacts the interfacial strength and toughness of bioinspired ceramics. Experimental and computational analysis reveals that higher mortar volumes increase energy dissipation but reduce interfacial stiffness, offering insights for ...
Ehsan Azad, Hamidreza Yazdani Sarvestani, Behnam Ashrafi, Farjad Shadmehri, Mehdi Hojjati   +4 more
wiley   +1 more source