Results 71 to 80 of about 922,436 (391)

Realization of Borehol V1 Till V4 at Liquidation of Shaft Leopold Situated in the Solivar Part of the Town of Presov [PDF]

open access: yesActa Montanistica Slovaca, 2004
Leopold shaft is situated in the Solivar part of the town of Presov, object (object of National Cultural Monument Gapla). Strong ascent of the level of natural salt brine resulted in the change of stress state of rock massif with subsequent deformation ...
Wittenberger Gabriel   +4 more
doaj  

Use of Disaster Management Computerized Simulation System in a teaching hospital of Tehran University of Medical Sciences [PDF]

open access: yesحیات, 2004
Introduction: With a dramatic increase in costly mass casualty incidents over the past few decades, disaster planning and preparedness now represent a prominent part of health care policy and practice.
J Nasl Seraji, H Dargahi
doaj   +1 more source

Chuck for delicate drills [PDF]

open access: yes, 1972
Development of oil film technique to couple power between drive spindle and drill chuck for delicate drilling operations is discussed. Oil film permits application of sufficient pressure, but stops rotating when drill jams.
Copeland, C. S.
core   +1 more source

Sites M0001–M0004 [PDF]

open access: yes, 2006
Operations Mobilization of Vidar Viking, Aberdeen, ScotlandThe Vidar Viking came under contract on 22 July 2004, when mobilization began in Aberdeen, Scotland.
Backman, J.   +30 more
core   +1 more source

Development of Ternary Magnesium Alloys for Laser Powder Bed Fusion: Optimizing Oxide Layer Thickness

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing of magnesium alloys by laser is difficult because the melting point of the oxide layer is much higher than the evaporation temperature of the metal underneath. Making the oxide layer thinner can solve this problem. Alloying magnesium with strontium makes the oxide layer thinner, especially at 0.5 wt%.
Elmar Jonas Breitbach   +8 more
wiley   +1 more source

Core drill's bit is replaceable without withdrawal of drill stem - A concept [PDF]

open access: yes, 1970
Drill bit is divided into several sectors. When collapsed, the outside diameter is forced down the drill stem, when it reaches bottom the sectors are forced outward and form a cutting bit.
Rushing, F. C., Simon, A. B.
core   +1 more source

Anomaly Detection Method for Hybrid Workpieces Using Dynamic Time Warping

open access: yesAdvanced Engineering Materials, EarlyView.
Monitoring of hybrid workpieces: when machining hybrid workpieces, unavoidable axial deviations of the material transition zone cause temporal shifts in the process force signals. A new anomaly detection method based on dynamic time warping is proposed to detect material defects.
Berend Denkena   +3 more
wiley   +1 more source

Hanging Ball and Handpad Drill Training: Which is better in improving the ability of the instep serve in Sepak Takraw?

open access: yesSriwijaya Journal of Sport
The Sepak Takraw game requires precise and programmed training to produce accurate serves. This research aims to determine the effect of hanging ball and hand pad drills (Target) on improving instep serviceability in Sepak Takraw.
Ummu Amalia Ulfa   +4 more
doaj   +1 more source

PENGARUH PROJECT BASED LEARNING DENGAN METODE DRILL DAN PROJECT BASED LEARNING DENGAN METODE FEEDBACK TERHADAP HASIL BELAJAR PEMROGRAMAN WEB

open access: yesTeknologi dan Kejuruan, 2018
Tujuan penelitian adalah mengungkap perbedaan rerata hasil belajar pem­rog­raman web (ranah pengetahuan dan keterampilan) karena pengaruh penerapan PjBL dan Metode Drill dibandingkan dengan PjBL dan metode Feedback.
Syaichul Fitrian Akbar   +2 more
doaj   +1 more source

Hindi Drill Patterns [PDF]

open access: yes
These ‘drill patterns’ follow the order of Beginner’s Hindi but can of course be used quite independently of this book. They are designed to help you assimilate the essential structures of Hindi.
Snell, Rupert
core   +1 more source

Home - About - Disclaimer - Privacy