Results 41 to 50 of about 432,547 (311)

Drilling Burr Minimization by Changing Drill Geometry [PDF]

Materials, 2020
This article presents an attempt to solve the problem of the formation of burrs and drilling caps in the process of drilling in difficult-to-cut materials, specifically in the titanium alloy Ti-6Al-4V. In order to eliminate these phenomena, a chamfer of specific length and angle was made on FANAR drill’s margin.
Emilia Franczyk, Łukasz Ślusarczyk, Wojciech Zębala   +2 more
openaire   +2 more sources

Comparing the Effect of Semi‐Immersive Virtual Reality, Computerized Cognitive Training, and Traditional Rehabilitation on Cognitive Function in Multiple Sclerosis: A Randomized Clinical Trial

Annals of Clinical and Translational Neurology, EarlyView.
ABSTRACT Background Cognitive impairment is a common non‐motor symptom in Multiple Sclerosis (MS), negatively affecting autonomy and Quality of Life (QoL). Innovative rehabilitation strategies, such as semi‐immersive virtual reality (VR) and computerized cognitive training (CCT), may offer advantages over traditional cognitive rehabilitation (TCR ...
Maria Grazia Maggio, Desiree Latella, Lilla Bonanno, Paulo Cezar Rocha dos Santos, Marcos Maldonado‐Díaz, Meir Plotnik, Rosaria De Luca, Angelo Quartarone, Rocco Salvatore Calabrò   +8 more
wiley   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

Advanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal, Michael M. Becker, Sarah C. L. Fischer   +2 more
wiley   +1 more source

Control technology of drilling fluid performance in horizontal directional crossing of Tongming Strait by product pipeline

You-qi chuyun, 2021
As the environmental protection requirements for surrounding sea areas of Tongming Strait are high, the crossing strata are complex and changeable, the underground fresh water and sea water appear alternately, the crossing section is long with large ...
Yuguang MING, Chuanfu WANG, Qiang LAN, Hui LI, Zhendong LIU, Shuquan LYU   +5 more
doaj   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Experimental investigation of hole cleaning in directional drilling by using nano-enhanced water-based drilling fluids

Journal of Petroleum Science and Engineering, 2019
Inadequate hole cleaning often leads to challenges in drilling and well completion operations such as low rates of penetration, pipe sticking, losing tools, difficulties in liner/casing placements, etc.
Natalie Vanessa Boyou, I. Ismail, W. Sulaiman, Amin Sharifi Haddad, N. Husein, H. Hui, Kathigesu Nadaraja   +6 more
semanticscholar   +1 more source

Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy

Advanced Engineering Materials, EarlyView.
This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb, Zachary T. Kloenne, Samuel R. Rogers, Chi Hang Dominik Kwok, Mark C. Hardy, Michele S. Conroy, David Dye   +6 more
wiley   +1 more source

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

On the analysis of temperatures, surface morphologies and tool wear in drilling CFRP/Ti6Al4V stacks under different cutting sequence strategies

, 2020
In drilling CFRP/Ti6Al4V stacks, the cutting sequence strategy, which determines the coupling effects of each phase machining, affects significantly the machinability of the sandwiched material as well as the tool wear characteristics.
Jinyang Xu, Chao Li, Ming Chen, M. Mansori, J. Davim   +4 more
semanticscholar   +1 more source