Results 101 to 110 of about 98,529 (315)

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Identification and Localization of Wind Turbine Blade Faults Using Deep Learning

Applied Sciences
This study addresses the challenges inherent in the maintenance and inspection of wind turbines through the application of deep learning methodologies for fault detection on Wind Turbine Blades (WTBs).
Mason Davis, Edwin Nazario Dejesus, Mohammad Shekaramiz, Joshua Zander, Majid Memari   +4 more
doaj   +1 more source

Semantic Modeling in Materials Science and Engineering With Platform MaterialDigital Core Ontology 3.0

Advanced Engineering Materials, EarlyView.
The community‐driven Platform MaterialDigital Core Ontology (PMDco) 3.0 is introduced as a Basic Formal Ontology‐aligned semantic backbone for the processing–structure–properties paradigm in Materials Science and Engineering. Modular engineering, automated releases, and validation workflows are highlighted and key semantic patterns for materials ...
Markus Schilling, Philipp von Hartrott, Jörg Waitelonis, Thomas Hanke, Henk Birkholz, Hossein Beygi Nasrabadi, Khashayar Razghandi, Kamilla Zaripova, Felix Thonagel, Fabian Neuhaus, Martin Glauer, Lars Vogt, Harald Sack, Lutz Mädler, Bernd Bayerlein, Chris Eberl   +15 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Defect Detection and Classification on Wind Turbine Blades Using Deep Learning with Fuzzy Voting

Machines
Wind turbine inspections are traditionally performed by certified rope teams, a manual process that poses safety risks to personnel and leads to operational downtime, resulting in revenue loss. To address some of these challenges, this study explores the
Reed Pratt, Clark Allen, Mohammad A. S. Masoum, Abdennour Seibi   +3 more
doaj   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Receptor‐Free Identification of Toxic Gases Enabled by Hygroscopic Aqueous Salt Films

Advanced Functional Materials, EarlyView.
Water as a gas sensor coating sounds impossible—until it stops evaporating. Here, hygroscopic salt solutions (LiCl, LiBr, H3PO4) form non‐drying aqueous films on CNT chemiresistors under ambient air. Gases partition into these liquid layers, sometimes transforming into water, and generate salt‐specific resistance fingerprints across a four‐channel ...
Seongwoo Lee, Yun‐Tae Kim, Hwarang Choi, Sanghwan Park, Seongyeop Lim, Chang Young Lee   +5 more
wiley   +1 more source

Regulated Ion‐Diffusion Hydrogels for Subtle and Multimodal Temperature‐Strain Sensing in Wound Monitoring

Advanced Functional Materials, EarlyView.
A soft, dual‐channel hydrogel patch enables simultaneous detection of wound temperature and strain by integrating ion‐diffusion‐mediated thermoelectric and resistive sensing. The conformal design maintains stable performance during motion, capturing subtle inflammatory and mechanical changes for continuous wound monitoring.
Yu Fang, Xinglong Pan, Zhiwei Li, Wanheng Lu, Chang Liu, Yi Zhou, Guo Tian, Ghim Wei Ho   +7 more
wiley   +1 more source

A systematic survey: role of deep learning-based image anomaly detection in industrial inspection contexts

Frontiers in Robotics and AI
Industrial automation is rapidly evolving, encompassing tasks from initial assembly to final product quality inspection. Accurate anomaly detection is crucial for ensuring the reliability and robustness of automated systems.
Vinita Shukla, Amit Shukla, Surya Prakash S. K., Shraddha Shukla   +3 more
doaj   +1 more source

Chemical State Detection and Charge Transfer in Complex Oxide Heterostructures via In Situ Auger Electron Spectroscopy

Advanced Functional Materials, EarlyView.
In situ Auger Electron Spectroscopy resolves oxidation states with high fidelity during the pulsed laser deposition of multivalent perovskite manganate and vanadate heterostructures. The chemical‐state signature is carried by the valence‐electron population of the transition‐metal cation, read out through the relative intensities of Auger fine ...
Harish Kumarasubramanian, Jayakanth Ravichandran   +1 more
wiley   +1 more source