Results 171 to 180 of about 327,401 (350)

Size Measurement of Droplet

open access: yesJournal of the Research Association of Powder Technology, Japan, 1976
Kenichi Ushiki, Koichi Iinoya
openaire   +2 more sources

Perceived Impacts and Predictors of Cannabis Products used by Rheumatology Patients in Alberta: A Multivariable Analysis of Cross‐sectional Survey Data

open access: yesArthritis Care &Research, Accepted Article.
Objective This study aimed to characterize cannabis product choices (cannabinoid content and formulation) among rheumatology patients, and their associations with patient factors, patient reported perceived side effects and positive impacts. Methods An online survey (delivered from March to November 2022) was distributed by Alberta Health Services to ...
Susan Zhang   +10 more
wiley   +1 more source

Antimisting fuel breakup and flammability [PDF]

open access: yes
The breakup behavior and flammability of antimisting turbine fuels subjected to aerodynamic shear are investigated. Fuels tested were Jet A containing 0.3% FM-9 polymer at various levels of degradation ranging from virgin AMK to neat Jet A.
Fleeter, R., Parikh, P., Sarohia, V.
core   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

open access: yesAdvanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur   +5 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

open access: yesAdvanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi   +3 more
wiley   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

open access: yesAdvanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai   +2 more
wiley   +1 more source

How to Regulate the Migration Ability of Emulsions in Micro-Scale Pores: Droplet Size or Membrane Strength? [PDF]

open access: yesMolecules, 2023
Sun Q   +8 more
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

open access: yesAdvanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy