Results 201 to 210 of about 94,929 (301)

Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure

Advanced Engineering Materials, EarlyView.
Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari, Supharoek Sornsomrit, Muhammad Ayaz Akbar, Stephan Rudykh   +3 more
wiley   +1 more source

Soy Protein Isolate-Sodium Alginate Composite Particles for Stabilization of High Internal Phase Pickering Emulsions: Structural Characterization and Stabilization Mechanisms. [PDF]

Molecules
Yin Y, Li Y, Li N, Zhang H, Peng X.
europepmc   +1 more source

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Efficient preparation of size-controlled sodium alginate microspheres <i>via</i> adaptive Bayesian optimization of the spray process. [PDF]

RSC Adv
Feng S, Liu J, Li Z, Tao S.
europepmc   +1 more source

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Quantifying phage-host dynamics using droplet microfluidics. [PDF]

Nat Commun
Givelet L, von Schönberg S, Katzmeier F, Simmel FC.   +3 more
europepmc   +1 more source

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Study on mechanism of air distribution volume's influence on airflow, dust migration and spray dust reduction in fully mechanized caving face. [PDF]

Sci Rep
Hongjie Z, Shaocheng G, Tian Z, Deji J, Xi C, Xingyu C.   +5 more
europepmc   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Development of an Emulsion-Gel System Based on Corn Alcohol-Soluble Protein and Curdlan: Effects of Oil-to-Water Ratio and Shear Parameters. [PDF]

Gels
Li S, Wu C, Kang X, Wang R, Cui Q, Zhang Y, Liu M, Dou B, Liu Y, Chen H.   +9 more
europepmc   +1 more source