Results 91 to 100 of about 1,726,040 (290)

Determination of the Sampler Type and Rainfall Effect on the Deposition Fluxes of the Polychlorinated Biphenyls

The Scientific World Journal, 2012
Atmospheric concentration and deposition samples were collected between June 2008 and June 2009 in an urban sampling site Yavuzselim, Turkey. Eighty-three polychlorinated biphenyl (PCB) congeners were targeted in the collected samples.
Askin Birgül, Yücel Tasdemir
doaj   +1 more source

High‐Resolution Corrosion Fingerprinting of Alloy Libraries via Microdroplet Spectroelectrochemistry

Advanced Engineering Materials, EarlyView.
Ionic‐liquid microdroplet spectroelectrochemistry enables stable, localized electrochemical measurements over extended timescales. By coupling impedance spectroscopy, wetting analysis, finite‐element simulations, and operando Raman spectroscopy, it disentangles geometrical and electrochemical effects, opening new opportunities for rapid corrosion ...
Ekaterina Kurchavova, Oumaïma Gharbi, Mireille Turmine, Vincent Vivier   +3 more
wiley   +1 more source

Influence of Rough Flow over Sea Surface on Dry Atmospheric Deposition Velocities

Terrestrial, Atmospheric and Oceanic Sciences, 2013
A Meteorological model and a dry deposition module were used to estimate the effects of sea surface rough flow (SSRF) over the sea surface on dry deposition velocities. The dry deposition turbulence resistance, Ra, and sub-layer resistance, Rb, decreased
Yan Zhang, Weichun Ma, Limin Chen
doaj   +1 more source

OntOMat: Toward Ontology‐Based Product and Process Design Engineering and Optimization Solutions Fueling Circular Value Chains

Advanced Engineering Materials, EarlyView.
The OntOMat ontology establishes a structured framework for polymer matrix fiber reinforced composite materials, integrating manufacturing processes, characterization methods, and multiscale design through the VDI/VDE 3682 formalized process description standard.
Nicolas Christ, Jörg Hohe, Martin Kördel, Michael Giese, Niklas Toffert, Christian Seidel, Olaf Rehme, Patrik Schneider, Oliver Focke, Elie Abi Aoun, Claas Falldorf, Beñat Gutierrez, Alexandra Kühn, Sven Torstrick-von der Lieth, Christoph Herden, Erik Johannsen, Jan‐Uwe R. Schmidt, Felix Winkelmann, Andreas Schott, Daniel Schott   +19 more
wiley   +1 more source

Deposition processes of ionic constituents to snow cover [PDF]

, 2010
Atmospheric deposition is an important removal process of aerosol particles and gases from the atmosphere. To elucidate the relative contributions of wet and dry processes and in-cloud and below-cloud scavenging based on deposition amounts in winter at ...
Osada, K., Iida, H., Shido, Y., Kido, M.
core   +1 more source

Uniform Amorphization of Crystalline Silicon Surfaces Enabled by Deep Ultraviolet Femtosecond Laser Pulses

Advanced Engineering Materials, EarlyView.
Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali, Magali Gregoire, Matys Guyard, Tatiana Itina, David Grojo, Pol Sopeña   +5 more
wiley   +1 more source

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Dry deep drawing of aluminum for automotive production

, 2020
Lubricants are commonly used in metal forming processes to reduce the friction between the workpiece and the forming tool to protect semi-finished products and goods against corrosion and to reduce the load on the tool.
Börner, Richard, Scholz, Peter, Schubert, Andreas, Vollertsen, Frank, Kühn, Ralf, Prieske, Markus, Berger, Thomas, Müller, Roland   +7 more
core   +2 more sources

Characterization of Wet and Dry Deposition in the Downwind of Industrial Sources in a Dry Tropical Area

The Scientific World Journal, 2001
An atmospheric deposition study was conducted in the downwind of Shaktinagar Thermal Power Plant (STPP), Renusagar Thermal Power Plant (RTPP), and Anpara Thermal Power Plant (ATPP), at Singrauli region, Uttar Pradesh (UP), India to characterize dry and ...
Raj K. Singh, Raj M. Agrawal
doaj   +1 more source