Results 201 to 210 of about 310,495 (356)

Development of an energy-efficient indirect type dryer using a triangular duct solar air heater with the synergistic effect of pin-fins and discrete V-ribs: A 3-D CFD study. [PDF]

Sci Rep
Sushmitha M, Gadepalli P, Nidhul K.
europepmc   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Drying kinetics, power consumption, economic and environmental analysis of pomegranate peels drying using a hybrid solar dryer compared with oven dryer. [PDF]

Sci Rep
Metwally KA, Khater EG, Bahnasawy AH, Tantawy AA, Elbeltagi A, Salem A, Marey SA, Okasha AM, Ali KAM, Elwakeel AE.   +9 more
europepmc   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Enhancement solar dryer performance and collector efficiency of paraffin PCM/copper fin featured solar dryer. [PDF]

Sci Rep
Venkatesh R, Sharma P, Subbarao CC, Mohanavel V, Veerababu K, Jadhav A, Ravichandran M, Soudagar MEM, Alotaibi MA, Sivanraju R.   +9 more
europepmc   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Performance evaluation of a triple-sided solar dryer in terms of energy-exergy analysis, sustainable indicators and CFD simulation during drying tilapia fish strips. [PDF]

Sci Rep
Ghanem THM, Oraiath AAT, Nsasrat LS, Ali G, Younis OS, Eldin AZ, Elmolakab KM, Alhumedi M, Ahmed AF, Tantawy AA, Elwakeel AE.   +10 more
europepmc   +1 more source

Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter, Felix Drechsler, Till M. J. Stadtmüller, Cameliu Himcinschi, Christos G. Aneziris, Jens Kortus   +5 more
wiley   +1 more source

TRPC6 effects on albumin permeation, nephrin shedding, and apoptosis in podocytes: Role of calcineurin and metalloproteases. [PDF]

Physiol Rep
Kim EY, Dryer SE.
europepmc   +1 more source

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source