Results 141 to 150 of about 2,849,574 (209)

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Green Technology Applying Heat Pump Drying, Modelling and Simulation

, 2014
This work has focused on the development of atmospheric freeze and non-freeze drying applying a heat pump system as an environmental friendly and economically preferable technology compare to vacuum freeze drying.
Mukhatov, Kirill
core  

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

Digital Light Processing of Thermoplastic Poly(methyl methacrylate) Photoresin Combined With Solvent Vapor Smoothing

Advanced Engineering Materials, EarlyView.
A thermoplastic PMMA‐based photoresin enables high‐resolution DLP printing followed by solvent‐vapor smoothing. The treatment reduces staircase‐induced surface roughness from 2.33 µm to 129 nm and increases visible‐light transmittance from approximately 30% to 80%, providing a route toward transparent PMMA components for rapid prototyping and non ...
Rozhin Heydarpour, Yuanyuan Li, Sebastian Kluck, Afnan Qazzazie‐Hauser, Bastian E. Rapp, Frederik Kotz‐Helmer   +5 more
wiley   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

Advanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi, M. N. Wengenmeyr, J. Bartsch, B. E. Rapp   +3 more
wiley   +1 more source

Gyroid Structured Globugraphite Carbon Foam With Hierarchical and Tailored Pore Size

Advanced Engineering Materials, EarlyView.
Secondary sacrificial templates were designed and printed to create a defined network within a porous carbon. Lattices thermally degrades during the sintering process. Lattices are imprinted into the ceramic template and transferred to the morphology of Globugraphite.
Christiane Roller, Justin Neumann, David Ploch, Lennard M. Flohr, Julian Karsten, Fabian A. Riebesehl, Bodo Fiedler   +6 more
wiley   +1 more source

Influence of Fe Particle Size Distribution on Chemical Homogeneity, Microstructure, and Crack Formation in Fe–SiC Powder Blends Processed by PBF‐LB/M

Advanced Engineering Materials, EarlyView.
The influence of Fe particle size on in situ alloying of Fe–SiC powder blends in PBF‐LB/M is revealed. Contrary to expectations, the coarser Fe fraction provides a broader crack‐free processing window and slightly improved elemental homogeneity while producing higher but more variable hardness. The results highlight a complex trade‐off between particle
Anna Luise Strauch, Anastasiya Toenjes, Matthias Steinbacher   +2 more
wiley   +1 more source

Edible Cuttlefish Ink: Complex Chemistry, Structure, and Electrical Response

Advanced Engineering Materials, EarlyView.
An integrated approach of chemistry‐structure‐electrical properties is used to assess the potential of edible cuttlefish ink as a bio‐based conductive ink for printable electronics. Chromatography and Neutron Activation Analysis reveal a fascinating molecular and elemental diversity.
Camille Bour‐Cardinal, Darren Hall, Teresa Cecchi, Sara Offidani, Philippe Plamondon, Clara Santato   +5 more
wiley   +1 more source