Results 141 to 150 of about 3,047,303 (249)

Effect of Partial Root Drying Stress on Improvement in Tomato Production. [PDF]

Curr Issues Mol Biol
Xu H, Jing H, Shi R, Chen M, Wang C, Xu Q, Bai J, Liu X, Kong M.   +8 more
europepmc   +1 more source

Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy

Advanced Engineering Materials, EarlyView.
An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa, Jeverton L. Paixão, Daylla S. Silva, Bruno S. Sobral, Mucio D. de Medeiros, José E. Spinelli, Bismarck L. Silva   +6 more
wiley   +1 more source

FastNano Liquid: An Automated Platform for Small‐Angle X‐ray Scattering‐Based Materials Discovery

Advanced Engineering Materials, EarlyView.
We present FastNano Liquid, an automated small‐ and wide‐angle X‐ray scattering platform for the combined synthesis and characterization of (nano)materials. The platform is coupled to varied reactor workflows for both in situ studies of reaction kinetics and ex situ screening of synthesis conditions to support machine learning‐guided exploration ...
Pierre‐Baptiste Flandrin, Émeline Cournède, Jens Krarup, Michael Lesa, Foyzul Hasan, Amandine Séné, Arnaud Lahouati, David Benhaiem, Jérémie‐Luc Sanchez, Simon Delacroix, Thierry Gacoin, Fabienne Testard, Damien Faivre, David Carriere, Corinne Chevallard, Olivier Taché, Mark A. Levenstein   +16 more
wiley   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

A Porosity-Dependent Constitutive Model for Concrete Under Wetting-Drying Cycles: Experimental and Field Validation. [PDF]

Materials (Basel)
Zhang X, Sun G, Li T, Shu J.
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Enhancing Food Quality Through Radio Frequency Drying of In-Shell Oil Crops: A Critical Review of Mechanisms, Advantages, and Challenges. [PDF]

Compr Rev Food Sci Food Saf
Xie Y, Guo J, Geng J, Xu C, Wang D, Zhao Y, Liu Y, Duan X, Lu F.   +8 more
europepmc   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Alternating Wetting and Drying Irrigation During Grain Filling Period Improves the Eating Quality and 2AP Content of Aromatic Rice. [PDF]

Plants (Basel)
Zhang Z, Li Q, Li G, Chen L, Xie X, Zeng Y.   +5 more
europepmc   +1 more source