Results 111 to 120 of about 469,103 (345)
MiX: A Position Sensitive Dual-Phase Liquid Xenon Detector
, 2015 The need for precise characterization of dual-phase xenon detectors has grown as the technology has matured into a state of high efficacy for rare event searches.
Haefner, J. +10 more
core +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories
Advanced Engineering Materials, EarlyView.Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Effect of Heat Treatment on Performance of 2205 Base Equipment and Pipes
Engineering Reports2205 dual‐phase stainless steel is widely used in petrochemical equipment. This paper simulates welding, post‐weld heat treatment, and operation conditions of 2205 steel.
Yajun Li +4 more
doaj +1 more source
A new test procedure to validate tensile dynamic mechanical properties of sheet metals and alloys in automotive crash applications [PDF]
, 2008 A thin walled open channel beam subjected to a 3-point bend and constant velocity boundary condition is investigated to establish its potential to validate material performance for automotive crash applications.
Buckley, M.A., Schley, C.A., Wood, Paul
core
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Metastable austenite driven work-hardening behaviour in a TRIP-assisted dual phase steel
, 2017 The mechanically-induced transformation behaviour of the metastable austenite phase in a high-strength industrial TRIP-assisted Dual Phase steel was monitored in situ using high-energy synchrotron diffraction under uniaxial loading.
B. Ennis +8 more
semanticscholar +1 more source
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
Advanced Engineering Materials, EarlyView.This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
MetalsThe volume fractions of martensite and ferrite in dual-phase steel affect its strength and plasticity. In this study, the effect of heat treatment on the structure morphology and volume fractions of martensitic and ferrite was studied in rare earth ...
Zhishen Li +5 more
doaj +1 more source