Results 31 to 40 of about 6,850 (263)

Permeability and seismic velocity anisotropy across a ductile–brittle fault zone in crystalline rock [PDF]

Solid Earth, 2018
This study characterizes the elastic and fluid flow properties systematically across a ductile–brittle fault zone in crystalline rock at the Grimsel Test Site underground research laboratory.
Q. C. Wenning, C. Madonna, A. de Haller, J.-P. Burg   +3 more
doaj   +1 more source

Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys

Advanced Engineering Materials, EarlyView.
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak, Olha Zvirko, Rostyslav Leshchak, Hryhoriy Nykyforchyn   +3 more
wiley   +1 more source

EXPERIMENTAL INVESTIGATION OF THE FAILURE BEHAVIOUR OF POLYPROPYLENE COMPOUNDS FOR INSTRUMENTED PUNCTURE TESTS

Acta Polytechnica CTU Proceedings, 2018
Instrumented puncture tests according to ISO 6603-2 and ASTMD3763 were executed for five different Polypropylene compounds (talcum-, glass fibre- and elastomer modified) with specimen thicknesses ranging from 1mm to 4 mm.
Florian Kiehas, Anna Kalteis, Michael Jerabek, Zoltán Major   +3 more
doaj   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Ductile-to-brittle transition behavior of X52 line pipe steel at low temperatures and its implications for crack arrest in CO2 pipelines

管道保护
During CO2 leakage, the Joule-Thomson effect and operational factors such as throttling and venting can cause the local temperature of the pipeline to drop abruptly to -78.5 ℃, significantly increasing the risk of brittle fracture.
Yi ZHANG, Lei SHI, Yi SHUAI, Liguo ZHOU, Cong TANG   +4 more
doaj   +1 more source

Numerical Modeling of the Ductile-Brittle Transition [PDF]

Le Journal de Physique IV, 1996
Numerical studies of the ductile-brittle transition are described that are based on incorporating physically based models of the competing fracture mechanisms into the material's constitutive relation. An elastic-viscoplastic constitutive relation for a porous plastic solid is used to model ductile fracture by the nucleation and subsequent growth of ...
openaire   +2 more sources

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Some Aspects of Structural Modeling of Damage Accumulation and Fracture Processes in Metal Structures at Low Temperature

Modelling and Simulation in Engineering, 2016
The problem of brittle fracture of structures at low temperature conditions connected to damage accumulation and ductile-brittle transition in metals. The data for locomotive tire contact impact fatigue and spalling are presented.
Valeriy Lepov, Albert Grigoriev, Valentina Achikasova, Kyunna Lepova   +3 more
doaj   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source