Results 221 to 230 of about 41,365 (304)

On the Mechanical and Thermal Behavior of PLA, PBAT, and PHBV‐Based Ternary Blends and the Effect of Short Flax Fibers as Reinforcing Agents

Polymer Composites, EarlyView.
Preparation and testing of biodegradable polymer ternary blends and composites with short flax fibres. ABSTRACT Bioplastics offer environmental benefits but they are costly and exhibit lower mechanical and thermal performance compared to fossil‐based counterparts. Poly(butylene adipate‐co‐terephthalate) (PBAT) exhibits high ductility but relatively low
Alessia Pantaleoni, Irene Bavasso, Maria Paola Bracciale, Claudia Sergi, Pietro Russo, Jacopo Tirillò, Fabrizio Sarasini   +6 more
wiley   +1 more source

Micro-Mechanical Properties and Deformation Damage Behavior of the Matrix and Primary Carbides in 8Cr4Mo4V Bearing Steel. [PDF]

Micromachines (Basel)
Sun C, Fan X, Shi X, Liu J, Zhang Z, Zhang B, Liu H.   +6 more
europepmc   +1 more source

Accelerated Degradation of PLA‐Based Composites in Harsh Alkaline Environment

Polymer Composites, EarlyView.
Evolution of surface properties and features of RP sample treated in harsh conditions: FTIR and wetting analysis. ABSTRACT The performance of poly(lactic acid) (PLA) bioplastics under harsh service conditions must be understood to enable their use in multi‐use products.
Cristina Moliner, Alberto Lagazzo, Juan Felipe Basbus, Roberto Raiteri, Elisabetta Finocchio, Elisabetta Arato   +5 more
wiley   +1 more source

Effect of Surfactant-Added Oil on the Physical Properties of Fried Coating for Deep-Fried Foods Obtained under Various Frying Conditions. [PDF]

J Appl Glycosci (1999)
Ogami M, Aoyagi K, Otsuki T, Uehara H, Kawai K.   +4 more
europepmc   +1 more source

Evaluation of Fiber‐Matrix Debonding in Glass, Carbon, and Hybrid Fiber Composites Under Transverse Loading by Full‐Field Measurements

Polymer Composites, EarlyView.
An experimental multiscale approach to investigate how fiber spacing, orientation, and material hybridization influence fiber‐matrix debonding and transverse cracking. ABSTRACT This study aims to experimentally quantify fiber‐matrix debonding and transverse crack evolution in single‐fiber and double‐fiber composite specimens, with particular emphasis ...
Zaynab Hazaveh, Behrad Koohbor
wiley   +1 more source

Structural Evolution and Mechanical Modulation of C_f/SiC Interfaces During PIP Ceramization: A ReaxFF Molecular Dynamics Study. [PDF]

Polymers (Basel)
Zhan Y, Wang X, Guan K, Lv M, Peng C, Yang X, Bai L.   +6 more
europepmc   +1 more source

Behavior of a Novel Cyclic Olefin‐Based Hot‐Melt Adhesive in CFRP Adhesive Joints Compared to Conventional Epoxy‐Based Structural Adhesives

Polymer Composites, EarlyView.
Rate‐dependent performance of composite adhesive joints using thermoset and thermoplastic adhesives, in terms of toughness and fatigue behaviour. ABSTRACT A recently developed hot‐melt adhesive (HMA) based on cyclic olefin chemistry, supplied as a transparent, non‐tacky thermoplastic film with a distinctive polymer microstructure, was evaluated in this
Hossein Malekinejad, Ricardo J. C. Carbas, Eduardo A. S. Marques, Lucas F. M. da Silva   +3 more
wiley   +1 more source

Influence of reinforcement on the fracture surface characteristics of multistage solutionized and precipitation-hardened ternary Al-Mg-Si hybrid composites. [PDF]

Sci Rep
Shettar M, Kumar N, Hariharan G, Shankar G, Hegde A.   +4 more
europepmc   +1 more source

Masterbatch‐Assisted Fabrication of Polylactic Acid/Reduced Graphene Oxide Nanocomposites Exhibiting Mechanical Enhancement and UV‐C Aging Resistance

Polymer Composites, EarlyView.
Masterbatch‐Assisted Fabrication of Polylactic Acid/Reduced Graphene Oxide Nanocomposites. ABSTRACT Polylactic acid (PLA) is a promising bio‐based polymer; nonetheless, its extensive application is still limited by poor fracture toughness, low thermal stability, and strong susceptibility to degradation induced by ultraviolet (UV) radiation.
Maria Giovanna Pastore Carbone, Nikolaos Koutroumanis, George Paterakis, Julio Gomez, Costas Galiotis   +4 more
wiley   +1 more source

Multi‐Scale Characterization of PLA Composites With Natural‐Based Reinforcements: From Filament to 3D‐Printed Parts

Polymer Composites, EarlyView.
Thermal, microstructural, and mechanical characterization of 3D‐printed PLA composite parts. ABSTRACT To address plastic waste and agricultural residue underutilization, this study evaluates the thermal (DSC and FTIR), microstructural (SEM), and mechanical behavior of polylactic acid (PLA) reinforced with flax fibers and olive pit particles, processed ...
P. N. B. Reis, L. Távara, M. Muñoz‐Reja, M. T. Aranda, F. Nur Ainin, M. D. Azaman, L. M. Ferreira   +6 more
wiley   +1 more source