Results 201 to 210 of about 992,444 (308)

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Research on the Pavement Performance of Fiber-Reinforced High Modulus Asphalt Concrete. [PDF]

Polymers (Basel)
Chen G, Wang T, Yao Y.
europepmc   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Sustainable development beyond emissions: the role of ICT, load capacity factor, green technology patents, and energy transition in OECD countries. [PDF]

Sci Rep
Demirtas N, Okoth E, Sogut Y, Erdem A, Koseoglu Y, Sanver C.   +5 more
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Performance Evaluation of Hot Mix Asphalt Modified with Biomass-Based Waste Chestnut Shells as Filler Replacement. [PDF]

Materials (Basel)
İnce CB.
europepmc   +1 more source

Adjustment of Coatings Morphology and Particle Distribution of Layered Silicates by Freeze‐Drying for Improved Gas Barriers

Advanced Engineering Materials, EarlyView.
Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes, Moritz Bätcher, Andrea Deißenberger, Volkmar Stenzel, Andreas Hartwig   +4 more
wiley   +1 more source

Dataset of high-speed camera measurements from impact-tested reinforced concrete beams. [PDF]

Data Brief
Peterson V.
europepmc   +1 more source

Is Young's Modulus a Critical Coating Property Determining Fouling‐Release Performance of Marine Coatings?

Advanced Engineering Materials, EarlyView.
The release of foulers from protective marine coatings is determined by several interrelated material properties, including the strength of Young's modulus, the flexibility of chain segments, the surface free energy, and the magnitude of hydrodynamic stress.
Johann C. Schaal, Andreas Brinkmann, Andreas Hartwig   +2 more
wiley   +1 more source

Experimental validation of metaheuristic-optimized control for standalone DFIG dynamic performance enhancement. [PDF]

Sci Rep
Soued S, Boureguig K, Chabani MS, Himair Swhli KM.   +3 more
europepmc   +1 more source