Results 171 to 180 of about 22,473 (312)

Crystallographic Effects on Residual Relative Elastic Strain Heterogeneity Induced by Micro-Indentation in Non-Oriented Electrical Steels. [PDF]

Materials (Basel)
Adegboyega O, Brodusch N, Guichaoua L, Bessette S, Chromik RR, Gauvin R.   +5 more
europepmc   +1 more source

Increasing the Reuse Potential of High‐Strength Steels by Extending the Fatigue Life through Surface Treatments

steel research international, EarlyView.
Surface reconditioning through mechanical and electrochemical polishing is shown to extend the fatigue life of predamaged 42CrMo4 steel by over 12 times. By removing ≈100 μm of surface material, surface‐driven fatigue damage is mitigated. This study introduces a reuse potential metric to evaluate fatigue recovery and support sustainable steel reuse. To
Ayush Shrivastava, Oguz Gulbay, Srinivasa Raghavan Raghuraman, Marion Kreins, Fabian Weber, Peter Starke, Alexander Gramlich, Ulrich Krupp   +7 more
wiley   +1 more source

Subcritical cracking and sealing along cleavage planes and subgrain boundaries in plagioclase from the Mado Megamullion oceanic core complex. [PDF]

Sci Rep
Nimura K, Okudaira T, Michibayashi K.
europepmc   +1 more source

HWTS 50 Tool Steel Tailored for Laser Powder Bed Fusion: Sliding Wear of Bare Surfaces and Nitriding Response in Comparison with 18Ni300 and AISI H13

steel research international, EarlyView.
This work investigates the wear resistance and nitriding behavior of PBF‐LB/M‐processed Osprey HWTS 50, a lean hot work tool steel. Three heat treatment conditions are compared to conventional wrought H13, H11, and PBF‐LB/M 18Ni300. The study highlights HWTS 50's enhanced nitrogen diffusion, deeper nitriding hardness depth, and comparable or improved ...
Jonathan Hann, Giorgia Lupi, Sylvain Dossin, Riccardo Casati, Mandanà Moshiri, Arne Röttger, Faraz Deirmina   +6 more
wiley   +1 more source

SRGAN-Based Joint Super-Resolution and Denoising for Mitigating Geometric and Topological Biases in Fine-Grained Electron Backscatter Diffraction Images. [PDF]

Nanomaterials (Basel)
Li D, Chen X, Wang Y.
europepmc   +1 more source

Focussed beams for use in EBSD

IOP Conference Series: Materials Science and Engineering
Abstract Focussed beams (electrons, ions, and photons) are at the forefront of today’s and future scientific and engineering advanced research instruments. The beams are typically used for six purposes: imaging, detection, deposition, implantation, milling/ablation, and polishing.
openaire   +1 more source

In Situ Alloying of H13 Tool Steel With TiC via PBF‐LB/M

steel research international, EarlyView.
H13 tool steel is in situ alloyed with titanium carbides (TiC) in amounts up to 30 wt.%. This approach offers the advantage that the carbides melt only partially during processing, preventing excessive carbon enrichment of the steel matrix. The resulting microstructure consists of coarse, undissolved and fine, reprecipitated carbides, leading to grain ...
Oliver Bürgi, Anke Kaletsch, Christoph Broeckmann   +2 more
wiley   +1 more source

A Study on the Orientation Relationship and Interface Structure of the α₂ (Ti₃Al) and B2 Phases in the TiAl-Nb Sheets After Heat Treatment. [PDF]

Materials (Basel)
Liu J, Zhang L, Li M, Yao D, Niu Y, Li B, Song Y.   +6 more
europepmc   +1 more source

Microstructure, Defects, and Fatigue Response of High‐Strength Tool Steels

steel research international, EarlyView.
The martensitic tool steel family is designed for use in various working environments where they are subjected to repeatedly high mechanical loads. Despite the continuous upgrade of material´s microstructures through compositional development or processing techniques, defects remain a critical factor for the tool performance by leading to fatigue ...
Katerina Chantziara, Jens Bergström, Dimitrios Nikas, Mikael Thomas Grehk   +3 more
wiley   +1 more source

Crystallographic Anisotropies in α-SnWO₄ Photoelectrodes and Their Effects on Electronic Properties and Photoelectrochemical Performances. [PDF]

ACS Appl Mater Interfaces
Gottesman R, Fernandez E, Schwiddessen R, Abou-Ras D, Azulay D, Millo O, van de Krol R.   +6 more
europepmc   +1 more source