Results 91 to 100 of about 953,529 (268)

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Economic Valuation for Cidanau Watershed Area, Indonesia

Jurnal Manajemen Hutan Tropika, 2011
The paper describes economic valuation for the Cidanau watershed area of West Java in Indonesia. In this area natural resources deterioration has occurred even faster after the Asian Financial Crisis.
Kunihiko Yoshino, Budi Indra Setiawan, Hideki Furuya   +2 more
doaj  

Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies

Advanced Engineering Materials, EarlyView.
Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo, Daniela Winsley Valereto Friozi, Vinícius de Oliveira, Marcia Cristina Branciforti   +3 more
wiley   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source

Cost-Effectiveness of Bivalent Prefusion F Vaccine for Prevention of Respiratory Syncytial Virus Among Older Adults in Italy

ClinicoEconomics and Outcomes Research
Sergio Di Matteo,1 Paolo Bonanni,2 Sara Boccalini,2 Roberto Di Virgilio,3 Emma Lucia Fogliati,1 Giorgio Lorenzo Colombo4,5 1Center of Research, SAVE Studi - Health Economics and Outcomes Research, Milan, Italy; 2Department of Health Sciences, University ...
Di Matteo S, Bonanni P, Boccalini S, Di Virgilio R, Fogliati EL, Colombo GL   +5 more
doaj  

A Simplified Laminar Flow Model for the Pultrusion of Glass Fiber/Polyethylene Terephthalate Commingled Yarns

Advanced Engineering Materials, EarlyView.
A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares, Nadège Bouchonneau, Christian Jochum, Donald Radford   +3 more
wiley   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Understanding the Stochastic Nature of Process Parameter Development of Blown Powder Laser Beam Directed Energy Deposition Additive Manufacturing of Pure Molybdenum

Advanced Engineering Materials, EarlyView.
Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies, Daniel E. Driemeyer, Aaron P. Stebner   +2 more
wiley   +1 more source

Symbolic Regression and Multi‐Objective Optimization of the Flory–Huggins Interaction Parameter for Hydrogels

Advanced Engineering Materials, EarlyView.
We develop a data‐driven method to derive the mathematical expressions of the Flory–Huggins interaction parameter χ for the swelling behavior of temperature–responsive hydrogels. Starting from initial assumptions of χ, our workflow combines Bayesian optimization, Flory–Rehner theory, and symbolic regression to generate candidate χ expressions.
Yawen Wang, Adrian Ehrenhofer, Thomas Wallmersperger   +2 more
wiley   +1 more source