Results 131 to 140 of about 5,235,479 (357)

Advancing Wildfire‐Retardant Materials: Engineering Strategies for Direct and Indirect Suppression

Advanced Engineering Materials, EarlyView.
Here, the evolution, ecological impact, and performance of current fire‐retardant materials and suppression strategies are reviewed, offering an engineering perspective to address existing challenges and propose pathways for the development of more effective, scalable, and sustainable solutions to meet the demands of a changing climate. Wildfires cause
Changxin Dong, Samya Sen, Athena Kolli, Stewart G. Wilson, Eric Andrew Appel   +4 more
wiley   +1 more source

CALPHAD‐Guided Prediction and Interpretation of Phase Formation in Ta–Mo–Cr–Ti–Al Refractory High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
This study designs Ta–Mo–Cr–Ti–Al refractory high‐entropy alloys with a disordered body‐centered‐cubic A2 crystal structure aiming for improved ductility, lower density, and oxidation resistance. Four alloy compositions are identified by thermodynamic calculations.
Kateryna Khanchych, Chongchong Tang, Carsten Schroer, Björn Schäfer, Judith Jung, Michael Dürrschnabel, Ute Jäntsch, Bronislava Gorr   +7 more
wiley   +1 more source

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

Direct Electron Detection Electron Energy‐Loss Spectroscopy: Speeding Up 2D Analytical In Situ Transmission Electron Microscopy for Aluminum Alloys

Advanced Engineering Materials, EarlyView.
Scanning transmission electron microscopy imaging techniques are an essential tool to document dynamic developments, such as precipitation in aluminum alloys, during in situ heating experiments using transmission electron microscopy. However, in many cases, chemical information is required to interpret complex nanoscale processes.
Evelin Fisslthaler, Martina Dienstleder, Judith Lammer, Moritz Theissing, Daniel Knez   +4 more
wiley   +1 more source

BALTA SERC 3 Workplan - 2008-2009 [PDF]

, 2010
This is the annual research program plan of Social Economy Research Cluster (SERC) 3 of the BC-Alberta Social Economy Research Alliance (BALTA). SERC 3's mandate includes infrastructure, analysis and evaluation.BC-Alberta Social Economy Research Alliance
BC-Alberta Social Economy Research Alliance (BALTA)
core   +1 more source

Single‐Crystal Castability of CM186LC Nickel‐Based Superalloy

Advanced Engineering Materials, EarlyView.
The optimal conditions to obtain single‐crystal (SX) castings of the directional solidification nickel‐based superalloy CM186LC, are investigated. Cylindrical samples are cast via a proprietary SX Bridgman process. The effect of solidification rates (V) ranging from 1 to 10 mm⋅min−1 on the microstructure is explored.
André Baldissera, Sean Böhm, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

KÂZIMKARABEKİR İLÇESİNDE KARAMAN TARIM VE HAYVANCILIK

Selçuk Üniversitesi Sosyal Bilimler Enstitüsü Dergisi, 2008
Kâzımkarabekir, İç Anadolu Bölgesinin güneyinde Karaman iline bağlıbir ilçedir. KonyaKaraman yolu üzerinde bulunan ilçe, Karaman’a 23 km., Konya’ya 85 km uzaklıktadır. Güneyinde ve doğusunda, Karaman; kuzeyinde, Çumra; batısında, Güneysınır vardır.
Tahsin Tapur
doaj  

XXVI. Notice of several recent Discoveries in the Structure and Economy of Spiders. [PDF]

John Blackwall
openalex   +1 more source

NUCLEIC ACID ECONOMY IN BACTERIA INFECTED WITH BACTERIOPHAGE T2 [PDF]

, 1953
A. D. Hershey, June Dixon, Martha Chase
openalex   +1 more source

Impact of Various Rotary Friction Welding Process Parameters on the Mechanical Properties of a Steel–Aluminum Joint

Advanced Engineering Materials, EarlyView.
Rotary friction welding of steel E355 and the aluminum alloy EN AW‐6082 can lead to the formation of brittle intermetallic phases. The primary process parameters are varied in order to determine their influence on this intermetallic phase formation and the resulting mechanical properties.
Laura Huber, Phillipp Schultheiß, Michael Thiele, Christoph Rößler, Heinz Werner Höppel   +4 more
wiley   +1 more source