Results 161 to 170 of about 253,596 (293)

Corrections to the article "The metric dimension of graph with pendant\n edges" [Journal of Combinatorial Mathematics and Combinatorial Computing, 65\n (2008) 139--145] [PDF]

, 2010
Dorota Kuziak, Juan A. Rodríguez‐Velázquez, Ismael G. Yero   +2 more
openalex   +1 more source

Hip Morphology–Based Osteoarthritis Risk Prediction Models: Development and External Validation Using Individual Participant Data From the World COACH Consortium

Arthritis Care &Research, EarlyView.
Objective This study aims to develop hip morphology‐based radiographic hip osteoarthritis (RHOA) risk prediction models and investigates the added predictive value of hip morphology measurements and the generalizability to different populations. Methods We combined data from nine prospective cohort studies participating in the Worldwide Collaboration ...
Myrthe A. van den Berg, Fleur Boel, Michiel M. A. van Buuren, Noortje S. Riedstra, Jinchi Tang, Harbeer Ahedi, Nigel K. Arden, Sita M. A. Bierma‐Zeinstra, Cindy G. Boer, Flavia M. Cicuttini, Timothy F. Cootes, David T. Felson, Willem Paul Gielis, Joshua Heerey, Graeme Jones, Stefan Kluzek, Nancy E. Lane, Claudia Lindner, Joyce B. J. van Meurs, Andrea Mosler, Amanda E. Nelson, Michael C. Nevitt, Edwin H. Oei, Jos Runhaar, Harrie Weinans, Jesse H. Krijthe, Rintje Agricola   +26 more
wiley   +1 more source

Ultrasonography Compared With Computed Tomography in Identifying Thoracic Aortic Aneurysms in Patients With Giant Cell Arteritis

Arthritis Care &Research, EarlyView.
Objective The objectives of this study were to evaluate the correlation and agreement between ultrasonography and computed tomography (CT) in measuring ascending aorta diameter in patients with giant cell arteritis (GCA) and to investigate the development of new ascending aortic aneurysms in patients with newly diagnosed GCA.
Anne C. Bull Haaversen, Lene K. Brekke, Tanaz A. Kermani, Øyvind Molberg, Andreas P. Diamantopoulos   +4 more
wiley   +1 more source

Verification of a conjecture regarding Metric Dimension of a grid augmented with one edge

, 2020
Satvik Mashkaria
openalex   +2 more sources

Edge Metric Dimension of Honeycomb and Hexagonal Networks for IoT [PDF]

, 2021
Sohail Abbas, Zahid Raza, Nida Siddiqui, Faheem Khan, Taeg Keun Whangbo   +4 more
openalex   +1 more source

Hopfield Neural Networks for Online Constrained Parameter Estimation With Time‐Varying Dynamics and Disturbances

International Journal of Adaptive Control and Signal Processing, EarlyView.
This paper proposes two projector‐based Hopfield neural network (HNN) estimators for online, constrained parameter estimation under time‐varying data, additive disturbances, and slowly drifting physical parameters. The first is a constraint‐aware HNN that enforces linear equalities and inequalities (via slack neurons) and continuously tracks the ...
Miguel Pedro Silva
wiley   +1 more source

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

On the Edge Metric Dimension of Different Families of Möbius Networks [PDF]

, 2021
Bo Deng, Muhammad Faisal Nadeem, Muhammad Azeem   +2 more
openalex   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source