Results 11 to 20 of about 1,240,803 (294)
Fracture toughness of zirconia ceramic crowns made by feather-edge tooth preparation design [PDF]
Vojnosanitetski Pregled, 2012 Background/Aim. Fracture toughness determines functional crown strenght and prevents damages on ceramics during mastication. There is a lack of relevant literature data about fracture toughness of crowns made by feather-edge preparation.
Mirković Nemanja +3 more
doaj +4 more sources
Cutting edge radius preparation
Materials Today: Proceedings, 2020 Abstract The paper deals with the cutting edge preparation of milling tools by drag finishing. The aim was to determine the influence of parameters of cutting edge preparation on the cutting edge radius size of cemented carbide milling tools. The article describes the influence of cutting edge preparation on milling process, the tool treatment ...
Pokorný Peter +5 more
openaire +1 more source
Modeling simulation and analysis of textile pilling by using Upgraded Petri nets and two-level edge detection algorithm [PDF]
Tekstilna industrija, 2022 Upgraded Petri nets and a two-level edge detection algorithm for the modeling, simulation, detection, and analysis of textile pilling has used in this paper. There are two models in this paper.
Štrbac Perica +2 more
doaj +1 more source
Cutting edge preparation in machining processes [PDF]
Scientific Letters of Rzeszow University of Technology - Mechanics, 2013 In modern manufacturing industry it is essential to produce under low costs and high quality of products in a short time. This is possible by selecting the cutting parameters in order to achieve high accuracy and low processing time. Usually the desired cutting parameters are determined based on experience or by use of various handbooks but the cutting
Ladislav Kandráč +2 more
openaire +1 more source
Study on magnetic preparation of dual disk based on silica gel magneto-elastic abrasive particles
Xibei Gongye Daxue Xuebao, 2021 Magneto-elastic abrasive grains have magnetism, low elastic modulus and excellent abrasive performance, and have the characteristics of bonded abrasive grains and loose abrasive grains.
Zhao Xuefeng +5 more
doaj +1 more source
Influence of End Mill Manufacturing on Cutting Edge Quality and Wear Behavior
Journal of Manufacturing and Materials Processing, 2021 One of the decisive factors for the performance of milling tools is the quality of the cutting edge. The latter results from the process control of the individual steps along the tool manufacturing process chain, which generally includes the sintering or
Berend Denkena +3 more
doaj +1 more source
Modeling and detection of the prepared tool edge radius [PDF]
Science Progress, 2020 Introduction: High-speed and high-efficient machining is the inevitable development direction of machining technology. The tool edge preparation can improve the life, cutting performance, and surface quality of a tool and help to achieve high-speed and efficient machining.
Zhao Xuefeng, Li Hui, He Lin, Tao Meng
openaire +2 more sources
Preparation of edge states by shaking boundaries [PDF]
Annals of Physics, 2016 Preparing topological states of quantum matter, such as edge states, is one of the most important directions in condensed matter physics. In this work, we present a proposal to prepare edge states in Aubry-Andr$\acute{\textrm{e}}$-Harper (AAH) model with open boundaries, which takes advantage of Lyapunov control to design operations.
Shi, Z. C. +3 more
openaire +3 more sources
Edge computing-oriented scraper detection method for coal preparation plants
Gong-kuang zidonghua, 2021 The calculation amount of the current scraper detection method for coal preparation plants is large. Moreover, the method runs on the low-power, low-cost embedded Jetson Nano and has problems such as low execution efficiency and poor real-time ...
ZHANG Zhiqiang1 +3 more
doaj +1 more source
Suppression of tool wear by extremely short-duration cutting
Mechanical Engineering Journal, 2015 High-speed cutting has various advantages such as high material removal rates and reduction of machining time. However, the greatest problem of high-speed cutting is its excessive tool wear rate.
Yuki TERASAKA +3 more
doaj +1 more source