Results 131 to 140 of about 32,966 (269)
A Causal Examination of the Solar Influence on Holocene Climate
Geophysical Research Letters, Volume 53, Issue 17, 16 September 2026.Abstract Variations in Total Solar Irradiance (TSI) have long been hypothesized to influence global mean surface temperature (GMST) on multidecadal to millennial timescales, but empirical evidence has remained elusive. Here, we explore the link between solar variability and climate over the pre‐industrial Holocene, when anthropogenic influences were ...
Jordan P. Landers +5 more
wiley +1 more source
Utveckling av ett EDM-verktyg förkärnkraftsindustrin
, 2014 Electric Discharge Machining (EDM) is a machining method suitable for repair and maintenance operations in nuclear power plants. Crack removal and material sampling are two common operations where EDM is used in the nuclear power industry.
Kaya, Rabi, Ödling, Anders
core +2 more sources
Donor EDM sample demographics.
, 2018 Donor EDM sample demographics.
Andrew S. Goldstein (146415) +5 more
core +1 more source
Polymer Composites, Volume 47, Issue 17, Page 15689-15699, 10 September 2026.Effect of Mold Cavity Thickness on Consolidation Quality and Tensile Strength of CF/PEKK Composites. ABSTRACT Carbon‐fiber‐reinforced thermoplastic composites have attracted growing attention as high‐performance structural materials due to their superior toughness, shorter processing cycles, and recyclability.
Hyunseok Choi +3 more
wiley +1 more source
, 2010 EDM (Electrodischarge Machining) merupakan salah satu proses pemesinan nonkonvensional yang proses pengerjaannya memanfaatkan pelepasan bunga api listrik secara cepat dari elektroda (-) menuju benda kerja (+) melalui fluida dielektrik, dimana bunga api ...
Febrianto, Dwi Rahmad
core
Advanced Engineering Materials, Volume 28, Issue 17, 9 September 2026.Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies +2 more
wiley +1 more source
Advanced Engineering Materials, Volume 28, Issue 17, 9 September 2026.A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du +4 more
wiley +1 more source
Advanced Engineering Materials, Volume 28, Issue 17, 9 September 2026.The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat +5 more
wiley +1 more source
Developments in EDM process variables [PDF]
, 2011 . The electrical discharge machining (EDM) process parameters (both the input and output) are presented. The input variable of EDM presented here are electrical and non-electrical ones.
Mohammad , Yeakub Ali +2 more
core
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, Volume 28, Issue 17, 9 September 2026.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source