Results 121 to 130 of about 1,166,599 (282)

Mechanical and stress-strain behavior of hybrid fiber-reinforced metakaolin-based recycled aggregate concrete

Sustainable Buildings
This study investigates the effects of fiber on the mechanical performance and stress-strain characteristics of metakaolin-based recycled aggregate concrete (RAC).
Liu Ming-Ming, Liu Kang-Ning
doaj   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System

Advanced Engineering Materials, EarlyView.
Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner, Anna Sophie Jelinek, Velislava Terziyska, Peter Wagatha, Wolfram Knabl, Christian Mitterer, Helmut Clemens, David Holec   +7 more
wiley   +1 more source

Automatic Detection and Uncertainty Quantification of Landmarks on Elastic Curves. [PDF]

J Am Stat Assoc, 2019
Strait J, Chkrebtii O, Kurtek S.
europepmc   +1 more source

High‐Entropy Alloy Interlayers Toward Advanced Joining for High‐Performance Structural Applications: Current Progress and Emerging Challenges

Advanced Engineering Materials, EarlyView.
HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan, Jiafen Song, Jinglong Li, Jiangtao Xiong, Tao Yang   +4 more
wiley   +1 more source

Design of High Damping Elastic Metamaterial Based on Eddy Current Effects for Superior Vibration Attenuation

Shock and Vibration
Elastic metamaterials can achieve effective vibration suppression within a narrow bandgap frequency range but demonstrate limited vibration control capability outside the bandgap range.
Jian Yang, Cheng Shen, Han Meng
doaj   +1 more source

Experimental Study on the Mechanical Properties of Rock–Concrete Composite Specimens under Cyclic Loading

Buildings
The foundations of bridges and other tall buildings are often subjected to cyclic loads. Therefore, it is essential to investigate the mechanical properties of rock–concrete composite foundations under cyclic loads. In this paper, uniaxial cyclic loading
Hongjun Li, Baoyun Zhao, Zhengjun Hou, Hongyao Min   +3 more
doaj   +1 more source

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

Effect of Cu and CuP Additions on the Microstructure and Nanoindentation‐Based Fracture Behavior of CoNiAlSi Ferromagnetic Shape Memory Alloys

Advanced Engineering Materials, EarlyView.
Cu and combined Cu–P microalloying refine the microstructure and enhance the nanoindentation‐derived fracture resistance of CoNiAlSi ferromagnetic shape memory alloys without suppressing the martensitic transformation. Comparative SEM, DSC, and nanoindentation results reveal that the CuP‐containing alloy provides the most balanced response, achieving ...
Mehmet Demir
wiley   +1 more source