Results 71 to 80 of about 134,181 (290)

3D (Bio) Printing Combined Fiber Fabrication Methods for Tissue Engineering Applications: Possibilities and Limitations

Advanced Functional Materials, EarlyView.
Biofabrication aims at providing innovative technologies and tools for the fabrication of tissue‐like constructs for tissue engineering and regenerative medicine applications. By integrating multiple biofabrication technologies, such as 3D (bio) printing with fiber fabrication methods, it would be more realistic to reconstruct native tissue's ...
Waseem Kitana, Indra Apsite, Leonid Ionov   +2 more
wiley   +1 more source

Hybrid Routing, Modulation, Spectrum and Core Allocation Based on Mapping Scheme

Sensors, 2020
With the persistently growing popularity of internet traffic, telecom operators are forced to provide high-capacity, cost-efficient, and performance-adaptive connectivity solutions to fulfill the requirements and increase their returns.
Edson Rodrigues, Eduardo Cerqueira, Denis Rosário, Helder Oliveira   +3 more
doaj   +1 more source

REACTION: Research and experimental assessment of control plane architectures for in-operation flexgrid network re-optimization [PDF]

, 2015
CONNECT: The magazine from the GÉANT community. Issue 18, 2015.The REACTION project proposes, designs, and validates flexi-grid elastic optical networks enabling software-controlled high-rate transmissions.
Cugini, Filippo, Dallaglio, Mateo, Fernández Palacios, Juan Pedro, Gifre Renom, Lluís, López Álvarez, Victor, Velasco Esteban, Luis Domingo   +5 more
core  

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Automatic Hidden Elastic Optical Bypasses in Multi-Layer Networks

Applied Sciences
This paper focuses on handling traffic demands dynamically in a multi-layer IP-over-elastic optical network (IP-over-EON). We propose a mechanism that uses two types of optical resources.
Edyta Biernacka, Jerzy Domżał
doaj   +1 more source

Liquid-Liquid Phase Separation in an Elastic Network

, 2017
Living and engineered systems rely on the stable coexistence of two interspersed liquid phases. Yet surface tension drives their complete separation. Here we show that stable droplets of uniform and tuneable size can be produced through arrested phase ...
Dufresne, Eric R., Fanelli, Nicoló, Ijavi, Mahdiye, Sai, Tianqi, Smith-Mannschott, Katrina, Style, Robert W., Wilen, Lawrence A., Xu, Qin   +7 more
core   +2 more sources

3D‐Printed Sulfur‐Derived Polymers With Controlled Architectures for Lithium‐Sulfur Batteries

Advanced Functional Materials, EarlyView.
Rheology‐guided formulation design for direct ink writing enables the fabrication of 3D sulfur copolymer cathodes with controlled architectures for lithium‐sulfur batteries. The printed electrodes exhibit multiscale porosity and high sulfur utilization, delivering enhanced electrochemical performance compared to conventional cast electrodes.
Bin Ling, Haoran Wang, Pan Yang, Rishav Agrawal, Alex R. Neale, Laurence J. Hardwick, Tom Hasell, Esther García‐Tuñón   +7 more
wiley   +1 more source

Optical and mechanical properties of amorphous Mg-Si-O-N thin films deposited by reactive magnetron sputtering

, 2019
In this work, amorphous thin films in Mg-Si-O-N system were prepared in order to investigate the dependence of optical and mechanical properties on Mg composition.
Ali, Sharafat, Birch, Jens, Eklund, Per, Ekstrom, Erik, Jonson, Bo, Magnusson, Roger, Pallier, Camille, Paul, Biplab   +7 more
core   +1 more source

Smart, Bio‐Inspired Polymers and Bio‐Based Molecules Modified by Zwitterionic Motifs to Design Next‐Generation Materials for Medical Applications

Advanced Functional Materials, EarlyView.
Bio‐based and (semi‐)synthetic zwitterion‐modified novel materials and fully synthetic next‐generation alternatives show the importance of material design for different biomedical applications. The zwitterionic character affects the physiochemical behavior of the material and deepens the understanding of chemical interaction mechanisms within the ...
Theresa M. Lutz, Jonas De Breuck, Sahar Salehi, Meike N. Leiske   +3 more
wiley   +1 more source

PEDOT‐Based Eutectogel Electrode Arrays for Enhanced High‐Resolution Electrogastrography: Fabrication, Stability, and Wearable Performance

Advanced Functional Materials, EarlyView.
Here, we present a high‐density PEDOT eutectogel electrode array for enhanced body surface gastric mapping. Silver electrodes are blade‐coated onto flexible substrates, followed by electrogelation of PEDOT:PSS and the deposition of a PEDOT:LS eutectogel.
Christopher Slaughter, Luke Gatecliff, Xudong Tao, Ruben Ruiz‐Mateos Serrano, Amy T. Jin, Matias L. Picchio, Daniele Mantione, Antonio Dominguez‐Alfaro, George G. Malliaras   +8 more
wiley   +1 more source