Results 21 to 30 of about 174,186 (299)

Interactions, structure and properties in poly(lactic acid)/thermoplastic polymer blends [PDF]

open access: yes, 2014
Blends were prepared from poly(lactic acid) (PLA) and three thermoplastics, polystyrene (PS), polycarbonate (PC) and poly(methyl methacrylate) (PMMA). Rheological and mechanical properties, structure and component interactions were determined by various ...
B. Pukanszky   +5 more
core   +1 more source

Synergistic toughening effects of grafting modification and elastomer-olefin block copolymer addition on the fracture resistance of wood particle/polypropylene/elastomer composites

open access: yesMaterials & Design, 2019
A novel wood particle/polypropylene/elastomer composites with good impact resistance and stiffness was prepared by adding elastomer-olefin block copolymer (OBC) and grafting maleic anhydride (MAH) on polypropylene/OBC blends.
Shunmin Yi   +8 more
doaj   +1 more source

Improvement of partial discharge resistance of polypropylene under AC voltage by blending elastomer

open access: yesIET Science, Measurement & Technology, 2023
This paper reports on the partial discharge (PD) erosion characteristics of polypropylene (PP)/elastomer blends where ethylene‐octene copolymer elastomer (EOC) and propylene‐based elastomer are involved.
Yu Gao   +6 more
doaj   +1 more source

Assessment of microstructure, physical and thermal properties of bitumen modified with LDPE/GTR/elastomer ternary blends [PDF]

open access: yes, 2016
LDPE/GTR/elastomer ternary blends with variable LDPE/GTR ratio and constant elastomer content were prepared via melt-compounding. Obtained LDPE/GTR/elastomer blends were applied as thermoplastic modifiers into bitumen.
Sulkowski, Michal   +4 more
core   +1 more source

Diesel-Injection Equipment Parts Deterioration after Prolonged Use of Biodiesel

open access: yesEnergies, 2019
The application of biodiesel blends is known to significantly affect operation of diesel-injection equipment, especially the injectors and fuel pump.
Dimitrios N. Tziourtzioumis   +1 more
doaj   +1 more source

Elastomer Nanocomposites Based on Organoclay/IIR/EPDM: Microstructure and Mechanical Properties [PDF]

open access: yesعلوم و تکنولوژی پلیمر, 2013
Nanocomposite samples based on elastomer blends of butyl rubber (IIR) and ethylene propylene diene monomer (EPDM) were prepared using a laboratory scale two-roll mill in order to study the effect of Cloisite 15A organoclay content (i.e., 1, 3, 5 and 7 wt%
Laleh Basiri   +3 more
doaj   +1 more source

A Microrheological Study of Poly(Methyl Methacrylate) Elastomer/Poly(Ethylene Terephthalate) (PMMAelast/PET) Blends [PDF]

open access: yesMaterials Research, 2017
This study involved an evaluation of the influence of phase inversion in poly(methyl methacrylate) elastomer/poly(ethylene terephthalate) binary blends (PMMAelast/PET) and the effect of the addition of poly(methyl methacrylate-glycidyl methacrylate-ethyl
Juciklécia da Silva Reinaldo   +3 more
doaj   +2 more sources

Co-crosslinked blends of fluorosilicone elastomer and vinylidenefluoride polymers

open access: yes, 1993
A study was made of the compatibilisation of blends of fluorosilicone elastomer and crystalline fluorocarbon polymers, respectively poly(methyl-3,3,3-trifluoropropyl/methylvinylsiloxane) as the gum component and poly(vinylidenefluoridetetrafluoroethylene)
Soun-Hie Pak (7126622)
core   +4 more sources

Influence of thermally induced self‐assembly shish‐kebab crystal on charge transport behaviour in polypropylene/elastomer blends

open access: yesIET Science, Measurement & Technology, 2021
This paper reports on the influence of thermally induced self‐assembly shish‐kebab crystal on charge transport behaviour in polypropylene (PP) and PP/propylene‐based elastomer (PBE) blends.
Jing Li   +4 more
doaj   +1 more source

Fracture Behavior of Polypropylene /Elastomer Blends

open access: yesAdvanced Materials Research, 2008
In this paper, effort has been undertaken to study the fracture behavior of thermoplastic/elastomer (PP/SBS) dynamically vulcanized blends by analyzing the EWF test results. PP/SBS blends were prepared with concentrations of SBS of 15, 30 and 40 wt%.
Marianella Hern�ndez   +4 more
openaire   +1 more source

Home - About - Disclaimer - Privacy