Results 111 to 120 of about 210,818 (339)
, 2011 The results of diffuse neutron scattering experiment on PbMg1/3Nb2/3O3 single crystal above the Burns temperature are reported. It is shown that the high temperature elastic diffuse component is highly anisotropic in low-symmetry Brillouin zones and this
A. I. Rudskoy +7 more
core +1 more source
Conditioned place preference reveals ongoing pain in calves 3 weeks after disbudding. [PDF]
, 2020 Hot-iron disbudding, a routine procedure that prevents horn bud growth through cauterization, is painful for calves. The resulting burns remain sensitive to touch for weeks, but it is unknown whether calves experience ongoing, non-evoked pain.
Adcock, Sarah JJ, Tucker, Cassandra B
core
Colloidal Crack Sintering Lithography for Light‐Induced Patterning of Particle Assemblies
Advanced Functional Materials, EarlyView.Colloidal crack sintering lithography (CCSL) is a microfabrication technique that uses light‐induced photothermal heating to trigger sintering and controlled cracking in polymer colloidal assemblies. Local structural changes generate microchannels and patterns, enabling direct writing of diverse topographic motifs.
Marius Schoettle +2 more
wiley +1 more source
Unusual presentation of laryngotracheal injury due to electric burn
, 2020 Vikasdeep Gupta +4 more
openalex +2 more sources
Alkali Ion‐Incorporated HfO2 Dielectrics for Reconfigurable Neuromorphic Computing
Advanced Functional Materials, EarlyView.This work presents an indium gallium zinc oxide (IGZO) transistor with an alkali cation‐integrated hafnium dioxide (HfO2) dielectric exhibiting synaptic behavior via ion retention. The solution‐based film fabrication strategy overcomes the limitations of atomic layer deposition (ALD) and precursor coating, enabling the control of synaptic retention ...
Seung Yeon Ki +7 more
wiley +1 more source
Freezing of the local dynamics in the relaxor ferroelectric PZN-4.5PT
, 2012 We report measurements of the neutron diffuse scattering in a single crystal of the relaxor ferroelectric material 95.5%Pb(Zn1/3Nb2/3)O3-4.5%PbTiO3 (PZN-4.5%PT).
Gehring, P. M. +5 more
core +1 more source
Interconnected Porous Hydrogels with Tunable Anisotropy Through Aqueous Emulsion Bioprinting
Advanced Functional Materials, EarlyView.A 3D bioprintable microporous bioink is developed using an aqueous two‐phase system (ATPS) composed of extracellular matrix (ECM) mimetic biopolymers. The ATPS bioink enables the fabrication of interconnected porous architectures with up to 70% porosity, supporting long‐term cell viability and 3D cell alignment, enabling a simultaneous generation of ...
Hugo Edgar‐Vilar +4 more
wiley +1 more source
Robust and Reversible Thermofluorescence in Solvent‐Free Thermoplastic Polyurethane Composites
Advanced Functional Materials, EarlyView.Thermofluorescent polymer composites with high‐contrast optical outputs are prepared by solvent‐free blending of indenoquinacridone dye into a thermoplastic polyurethane matrix. The temperature‐dependent fluorescence originates from aggregation–dissociation of the dye molecules, regulated by competing hydrogen bonds from the polymer matrix.
Guanghua Yu +8 more
wiley +1 more source
A Clinical Analysis of Friction Burns Caused by Electric Scooters
, 2023 DoWon Kim +4 more
openalex +2 more sources
Advanced Functional Materials, EarlyView.The ultrahard teeth of mollusks that feed on rocky substrates contain a wear‐resistant coating on their surfaces consisting of densely packed mesocrystalline magnetic nanoparticles within an organic matrix. These coatings display significant hardness and toughness through their highly controlled mesocrystalline architectures.
Taifeng Wang +7 more
wiley +1 more source