Results 61 to 70 of about 28,678 (259)

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Enhancing Low‐Temperature Performance of Sodium‐Ion Batteries via Anion‐Solvent Interactions

Advanced Functional Materials, EarlyView.
DOL is introduced into electrolytes as a co‐solvent, increasing slat solubility, ion conductivity, and the de‐solvent process, and forming an anion‐rich solvent shell due to its high interaction with anion. With the above virtues, the batteries using this electrolyte exhibit excellent cycling stability at low temperatures. Abstract Sodium‐ion batteries
Cheng Zheng, Qian Yao, Yanan Sun, Hongyu Lv, Zhongchao Bai, Guoliang Zhang, Nana Wang, Jian Yang   +7 more
wiley   +1 more source

Electrical properties, conduction mechanism and modulus of diphosphate compounds

RSC Advances, 2016
Rubidium aluminium diphosphate was synthesized by a conventional solid-state technique and its conduction properties determined by impedance spectroscopy.
Y. Ben Taher, N. Moutia, A. Oueslati, M. Gargouri   +3 more
openaire   +1 more source

Dominant Role of Young’s Modulus for Electric Power Generation in PVDF–BaTiO3 Composite-Based Piezoelectric Nanogenerator

Nanomaterials, 2018
The electric power output of a piezoelectric nanogenerator (PENG) depends on the various physical parameters of the constituent materials, including the piezoelectric coefficient, Young’s modulus, and dielectric constant.
Hyun Soo Kim, Dong Woo Lee, Do Hyung Kim, Dae Sol Kong, Jinhyeok Choi, Minbaek Lee, Gonzalo Murillo, Jong Hoon Jung   +7 more
doaj   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Impedance and Electrical Modulus Study of Microwave-Sintered Ceramic

ISRN Ceramics, 2012
Bismuth layered structure SrBi2Ta2O9 ceramic is prepared by the microwave sintering technique via solid state route at 1100°C for 30 mins. X-ray diffraction analysis is used to analyze the phase purity, which identifies the orthorhombic structure with A21am space group.
V. Senthil, T. Badapanda, A. Chandra Bose, S. Panigrahi   +3 more
openaire   +1 more source

Electric and Dielectric Properties of Cotton and Regenerated Cellulose Fibers in Comparison with Polyethylene Terephthalate Fiber

Journal of Natural Fibers
The objective of this study is to look into the dielectric and ac-conductivity characteristics of Egyptian cotton and some regenerated cellulose fibers, i,e. viscose, bamboo, tencel, and modal fibers in comparison with PET fibers.
Alsaid Ahmed Almetwally, Heba M. Elfowaty   +1 more
doaj   +1 more source

Impedance, Electrical Equivalent Circuit (EEC) Modeling, Structural (FTIR and XRD), Dielectric, and Electric Modulus Study of MC-Based Ion-Conducting Solid Polymer Electrolytes. [PDF]

Materials (Basel), 2021
Faris BK, Hassan AA, Aziz SB, Brza MA, Abdullah AM, Abdalrahman AA, Abu Ali OA, Saleh DI.   +7 more
europepmc   +1 more source