Results 161 to 170 of about 3,182,073 (397)

Investigation of Iron‐Aluminide‐Like Phase Composition in Complex Concentrated Fe32Cu12Ni11Ti16Al29 Alloy

Advanced Engineering Materials, EarlyView.
This work reveals the phase composition and quantitative morphology analysis of precipitation‐hardened Fe32Cu12Ni11Ti16Al29 complex‐concentrated alloy. The precipitates are shown to have a high coherency. Morphology transition between sphere, cuboidal, and elongated morphology is observed. Finally, the overaging behavior is captured using microhardness.
Rostyslav Nizinkovskyi, Lukas Hanisch, Georg Hasemann, Puspendu Sahu, Manja Krüger   +4 more
wiley   +1 more source

Discussion: “Some Operating Data for Electric-Motor-Driven Reciprocating and Centrifugal Oil-Pipe-Line Pumps” (Stueve, W. H., 1930, Trans. ASME, 52(10), pp. 35–36) [PDF]

, 1930
John M. McGregor
openalex   +1 more source

Reactive Interaction and Wetting of Fe‐ and Mn‐Containing, Secondary AlSi Alloys with Manganese Oxide Ceramic Filter Material for Fe Removal

Advanced Engineering Materials, EarlyView.
Fe‐ and Mn‐containing AlSi alloys undergo aluminothermic reaction with Mn oxide in sessile‐drop and crucible experiments forming poor‐wetting Al2O3 while Mn enriches in the alloy. Primary Fe‐containing particles are preferentially attached to the Mn oxide.
Hanka Becker, Simon Waschull, Beate Fankhänel, Claudia Voigt, Alexandros Charitos, Christos G. Aneziris, Andreas Leineweber   +6 more
wiley   +1 more source

Concept for sleeve induction motor with 1-msec mechanical time constant [PDF]

, 1968
Conductive sleeve induction motor having a 1-msec mechanical time constant is used with solid-state devices to control all-electric servo power systems.
Wiegand, D. E.
core   +1 more source

On the Deformation Behavior of Metastable CrMnNi Steels Processed by Directed Energy Deposition in Different Temperature Regimes

Advanced Engineering Materials, EarlyView.
In the present study, metastable CrMnNi steels with varying chemical compositions and a concomitantly altered stacking fault energy are processed via directed energy deposition and afterwards tested via tensile tests at different temperatures. The present study shows the influence of the manufacturing process on the elemental deformation mechanisms for
Julia Richter, Thomas Wegener, Florian Stredak, Gert Bartzsch, Steffen Scherbring, Javad Mola, Olena Volkova, Stefan Böhm, Thomas Niendorf   +8 more
wiley   +1 more source

Optimization of Specific Power of Surface Mounted Axial Flux Permanent Magnet Brushless DC Motor for Electrical Vehicle Application

Iranian Journal of Electrical and Electronic Engineering, 2020
Optimization of specific power of axial flux permanent magnet brushless DC (PMBLDC) motor based on genetic algorithm optimization technique for an electric vehicle application is presented.
A. N. Patel, B. N. Suthar
doaj  

Analysis of Electric Motor Magnetic Core Loss under Axial Mechanical Stress. [PDF]

Sensors (Basel), 2020
Kumar LA, Madhan Raj B, Vijayakumar V, Indragandhi V, Subramaniyaswamy V, Karimi HR, Veluvolu KC.   +6 more
europepmc   +1 more source

New G-E Plastic insulates electric motors, permits higher ratings in smaller frames [PDF]

, 1957

openalex   +1 more source

Impact of Hot Isostatic Pressing on Microstructure Evolution and Creep Performance of Powder Bed Fusion–Laser Beam Processed CM247LC

Advanced Engineering Materials, EarlyView.
The influence of Hot Isostatic Pressing (HIP) temperature on the microstructure and creep performance of powder bed fusion–laser beam processed CM247LC superalloy is investigated. Grain growth and γ’ precipitate evolution are characterized following HIP at varying temperatures.
Ahmed Fardan, Johannes Gårdstam, Eva Oscarsson, Håkan Brodin, Eduard Hryha   +4 more
wiley   +1 more source

A study of electric motors for use in liquid and gaseous helium Engineering report no. 3530 [PDF]

Electric motor design and operation in liquid and gaseous helium ...
Bott, F. W., Caine, G. H., Pradhan, A. V.   +2 more
core   +1 more source