Results 131 to 140 of about 1,003,973 (291)
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Jurnal EdunitroInverter material is one of the essential materials in power electronics courses. An inverter is an electronic device that converts direct current (DC) into alternating current (AC). This concept is the foundation of electronics.
Dewi Suriani +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm +6 more
wiley +1 more source
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
Advanced Engineering Materials, EarlyView.This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir +7 more
wiley +1 more source