Results 231 to 240 of about 155,284 (320)
Automatic Exposure Volumetric Additive Manufacturing
Advanced Materials Technologies, EarlyView.Tomographic volumetric additive manufacturing (VAM) is resin‐based 3D printing technology, where objects are printed in seconds using volumetric light patterning. Although fast, tomographic VAM struggles to produce repeatable and accurate prints. This work demonstrates an automatic exposure method for tomographic VAM, resulting in commercial‐grade ...
Antony Orth +10 more
wiley +1 more source
Advanced Materials Technologies, EarlyView.This article investigates a sustainable approach to producing new powders for selective laser sintering by using high‐pressure homogenization to micronize biopolymers. The approach yields flowable, thermally stable particles with sub‐rounded morphology, enabling 3D printing of dense components with complex geometries.
Alberto Giubilini +5 more
wiley +1 more source
Dielectric Barrier Discharge Electrothermal Heating and Additive Manufacturing of Thermoset Parts
Advanced Materials Technologies, EarlyView.3D printing of thermosets is difficult due to the low yield stress of most uncured resins. However, by locally heating resin using a non‐equilibrium plasma, layers can be partially cured and printing enabled. Plasma application to a liquid epoxy/carbon nanotube composite is observed to cause rapid surface heating and oxidation of the cured layers ...
Ethan M. Harkin +3 more
wiley +1 more source
Dual‐Wavelength Vat Photopolymerization With Dissolvable, Recyclable Support Structures
Advanced Materials Technologies, EarlyView.Selective solubility vat photopolymerization (SSVP) uses a single resin to produce dissolvable thermoplastics and insoluble thermosets in a single 3D print. Wavelength‐selective curing and thermal post‐processing provide 3D spatial control over dissolution kinetics, enabling dissolvable support structures and programmable dissolution profiles.
Nicholas S. Diaco +7 more
wiley +1 more source
Advanced Optical Materials, Volume 13, Issue 8, March 13, 2025.Chalcogenide optical PCMs have gathered interest for their potential in compact, non‐volatile optics and photonics. Free‐space PCM metasurfaces require new considerations from phase change memory that need to be addressed for reliable scale‐up. Several failure mechanisms pertaining to free‐space PCM devices and layout methods are isolated to prevent ...
Cosmin Constantin Popescu +19 more
wiley +1 more source
Advanced Optical Materials, Volume 13, Issue 8, March 13, 2025.Correlative super‐resolution optical imaging of the ultrastructure of rat liver sinusoidal endothelial cells (LSECs) across a large field of view (FOV) with 3D structured illumination microscopy (3D‐SIM) and single‐molecule localization microscopy (SMLM), facilitated by a transparent polymer photonic waveguide chip, is presented.
Surjendu Bikash Dutta +9 more
wiley +1 more source
Energy Focusing Metasurface Based Wireless Power Transfer System for Compact Unmanned Mobilities
Advanced Optical Materials, EarlyView.A miniaturized wireless power transfer system integrates a metasurface lens, microstrip patch antenna, and RF‐CMOS rectifier to enhance mmWave reception efficiency and reduce size. Leveraging mmWave short wavelengths, it achieves high gain on small platforms. The system's polarization independence and wide‐angle reception ensure robust performance.
Wonwoo Lee +7 more
wiley +1 more source
Electrical burn causing a unique pattern of neurological injury. [PDF]
Plast Reconstr Surg Glob Open, 2015 Schaefer NR +4 more
europepmc +1 more source
Advanced Optical Materials, EarlyView.Laser‐induced graphene (LIG) on a colorless polyimide (CPI) substrate functions as both an electrical heater and a heat spreader, enabling rapid electro‐thermo‐optic actuation. The system achieves reflective beam scanning up to 2 kHz and diffractive beam steering with 0.5‐millidegree resolution and a 0.9 s response time, showcasing LIG‐CPI as a soft ...
Byunggi Kim +5 more
wiley +1 more source