Results 31 to 40 of about 4,534 (265)
Analysis of the Influence of Different EDM Parameters Using Taguchi Technique [PDF]
Engineering and Technology Journal, 2017 Electrical discharge machining (EDM) is a non-traditional material removal process developed in late 1940s has now become the most important technology in manufacturing industries.
S.H. Aghdeab, I.A. Qasim
doaj +1 more source
Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys
Advanced Engineering Materials, EarlyView.This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa +9 more
wiley +1 more source
Electrical Discharge Machining (EDM): A Review
International Journal of Engineering Materials and Manufacture, 2016 Electro discharge machining (EDM) process is a non-conventional and non-contact machining operation which is used in industry for high precision products.
Asfana Banu, Mohammad Yeakub Ali
doaj +1 more source
Advanced Engineering Materials, EarlyView.A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du +4 more
wiley +1 more source
Applied Sciences, 2021 The performance of electrical discharge machining for drilling holes decreases with machining depth because the conventional flushing and electrode cannot completely eliminate debris particles from the machining area.
Kamonpong Jamkamon, Pichai Janmanee
doaj +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The temperature dependence of fatigue behavior in nickel‐based superalloys is investigated through high‐resolution measurements of plastic localization. While increasing temperature reduces localization and enhances fatigue performance in René 88DT, Inconel 718 exhibits a sharp degradation at intermediate temperature due to intensified slip ...
M. Calvat +5 more
wiley +1 more source
Experimental Study on the Formation of Discharge Crater Morphology in Micro EDM [PDF]
한국정밀공학회지As advanced materials with high hardness, strength, and heat resistance are increasingly applied in fields such as aerospace, semiconductors, biomedical engineering, and mold manufacturing, the demand for high-precision machining technologies is growing.
Jae Yeon Kim +3 more
doaj +1 more source
Journal of the Japan Society for Precision Engineering, 1998 著者らが見い出した加工方法により, 絶縁性セラミックスも金属材料と同様な複雑形状加工が形彫りおよびワイヤ放電加工機により可能であることを簡単に紹介した.それほど難しい手法ではないので, 放電加工機を持つ現場で使用できると期待している.セラミックス材料の最大の難点であった加工技術の一手法として, 今後導電性セラミックス以上の加工特性を得るための方法・原理の確立が早急に望まれる.また, 放電現象を表面改質技術として利用する点からも, 基本的な加工原理を物理化学的な現象論の面からさらに追求する必要がある.
FUKUZAWA, Yasushi, MOHRI, Naotake
openaire +2 more sources
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source