Results 41 to 50 of about 4,917,957 (273)

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Retracted: A Study on Information Classification and Storage in Cloud Computing Data Centers Based on Group Collaborative Intelligent Clustering

Journal of Electrical and Computer Engineering, 2023
Journal of Electrical and Computer Engineering
doaj   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Retracted: Fault Diagnosis Method for UHVDC Transmission Based on Deep Learning under Cloud-Edge Architecture

Journal of Electrical and Computer Engineering, 2023
Journal of Electrical and Computer Engineering
doaj   +1 more source

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Genre analysis of introduction section in electrical engineering undergraduate laboratory reports. [PDF]

F1000Res, 2022
Veerappan V, Ahmad M, Balakrishnan K, Aris MA, Suan WH.   +4 more
europepmc   +1 more source

Retracted: Inbound Tourists’ Perception of Tourist Destination Image Classified by UGC Picture Computer Program

Journal of Electrical and Computer Engineering, 2023
Journal of Electrical and Computer Engineering
doaj   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

A Review of Environmentally Friendly Approaches in Fire Extinguishing: From Chemical Sciences to Innovations in Electrical Engineering. [PDF]

Polymers (Basel), 2022
Yılmaz-Atay H, Wilk-Jakubowski JL.
europepmc   +1 more source

Retracted: EEG Emotion Recognition Based on Temporal and Spatial Features of Sensitive signals

Journal of Electrical and Computer Engineering, 2023
Journal of Electrical and Computer Engineering
doaj   +1 more source