Results 101 to 110 of about 3,838,435 (315)

Research on protection block strategy of grounding faults in HVDC converter station

The Journal of Engineering, 2019
DC grounding fault is a typical fault for HVDC system. In order to obtain smoother, faster, and more secure transient process, the DC protection block strategy is used to remove and isolate the converter to prevent the accident enlargement and reduce the
Yichen Liu, Xiaoguang Zhu, Junbo Deng, Jie Guo, Fang Yu, Jiangtao Li   +5 more
doaj   +1 more source

Thermoelectric Modules Incorporating MgAgSb and Mg3(Sb,Bi)2 Synthesized Using a Melting Method

Advanced Engineering Materials, EarlyView.
A scalable synthesis method for a thermoelectric material of MgAgSb is established. A thermoelectric power module of MgAgSb/Mg3(Sb,Bi)2 is fabricated, showing the conversion efficiency of 7.4% at ΔT = 315 K. The performance is comparable to conventional Bi2Te3 modules when they are operated with an air‐cooled heat exchanger.
Kazuo Nagase, Hironori Ohshima, Kunihiro Kihou, Haruno Kunioka, Ushin Anazawa, Ryosuke Sakagami, Yosuke Goto, Masayuki Murata, Chul‐Ho Lee   +8 more
wiley   +1 more source

Soft start-up scheme for the hybrid distribution transformer

The Journal of Engineering, 2018
Hybrid distribution transformer (HDT) is an integrated system of the conventional distribution transformer and the PWM converters, which can greatly enhance the controllability of the conventional distribution transformer and is important for the ...
Yibin Liu, Deliang Liang, Mingkang Zhang, Yang Liang, Qixu Chen, Qingshan Wang   +5 more
doaj   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Carbon/graphite fiber risk analysis and assessment study: An assessment of the risk to Douglas commercial transport aircraft [PDF]

The potential hazard to electrical and electronic devices should there be a release of free carbon fibers due to an aircraft crash and fire was assessed. Exposure and equipment sensitivity data were compiled for a risk analysis.
Cook, C. Q., Gilles, D. L., Henning, B., Hosford, J., Schjelderup, H. C., Snyder, E., Swanstrom, C. W.   +6 more
core   +1 more source

Analysis of products from the pyrolysis of plastics recovered from the commercial scale recycling of waste electrical and electronic equipment [PDF]

, 2007
Three plastic fractions from a commercial waste electrical and electronic equipment (WEEE) processing plant were collected and investigated for the possibility of recycling them by batch pyrolysis. The first plastic was from equipment containing cathode
Hall, W.J., Williams, P.T.
core   +1 more source

Distribution of Electrical Resistivity in Single Carbon Fiber Filaments and Its Correlation With Tensile Modulus

Advanced Engineering Materials, EarlyView.
A statistical framework is applied to quantify the distribution of electrical resistivity among individual filaments of two commercially available carbon fiber types. Correlations between filament resistivity, tensile modulus, and diameter are examined and complemented by TEM analysis to provide new insight into filament‐level variability relevant for ...
Nils Wieja, Daniel Sebastian Wolz, Philip Johannes Steinbild, Markus Löffler, Darius Pohl, Jan Wolf, Anja Winkler, Thomas Behnisch, Bernd Rellinghaus, Maik Gude   +9 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

PLC Electric Control System of CNC Machine Tool

Chemical Engineering Transactions, 2017
This paper studied the design of PLC electrical control system of CNC machine tool. The design program of the electrical control system is established according to the requirements.
Jinghai Han
doaj   +1 more source

Electrical-power-system data base for consumables analysis. Volume 1: Electrical equipment list, activity blocks, and time lines [PDF]

A standardized data base is described which consists of a space shuttle electrical equipment list, activity blocks defining electrical equipment utilization, and activity-block time lines for specific mission analyses.
Green, P. A., Pipher, M. D., Wolfgram, D. F.   +2 more
core   +1 more source