Results 101 to 110 of about 119,088 (294)
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Investigation of Ag-Cu Alloys for Interconnects in IC [PDF]
EPJ Web of ConferencesCopper (Cu) has been the standard material of choice for interconnects in integrated circuits for decades because it has low resistivity (~1.68 µΩ·cm), high electrical conductivity, and is cost-effective.
S Aditya +4 more
doaj +1 more source
The influence of changes in water content on the electrical resistivity of a natural unsaturated loess [PDF]
, 2012 Non-destructive methods of measuring water content in soils have been extensively developed in the last decades, especially in soil science. Among these methods, the measurements based on the electrical resistivity are simple and reliable thanks to the ...
Cui, Yu Jun +3 more
core +3 more sources
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Thermal Conductivities and Electrical Resistivities of the Platinum Metals
Platinum Metals Review, 1962 New values are presented and discussed for the thermal conductivities and electrical resistivities of ruthenium, osmium, rhodium, iridium, palladium and platinum over the approximate temperature range 80° to 500°K.
R. W. Powell +2 more
openaire +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Preparation and characterization of Ni-Cu composite nanoparticles for conductive paints
Science and Engineering of Composite Materials, 2019 Ni and Cu are the two most promising alternatives to noble metals used in electrical conductive materials. However, Cu is susceptible to oxidation, while Ni exhibits poorer electrical conductivity.
Bai Liuyang
doaj +1 more source
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
International Journal of Lightweight Materials and ManufactureMica waste, a type of commercial waste produced in bulk quantities by the mica mining industry, was processed and added to Natural Rubber Latex Foams (NRLF) made of centrifuged and creamed latex.
Vimukthi Dananjaya +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source