Results 121 to 130 of about 116,293 (341)

Encapsulating Laser‐Induced Graphene to Preserve its Electrical Properties and Enhance its Mechanical Robustness

Advanced Engineering Materials, EarlyView.
It is demonstrated that laser‐induced graphene (LIG) can be encapsulated while preserving its electrical conductivity and enhancing its mechanical properties. Unlike previous encapsulation attempts, the optimal conditions described here result in sheet resistance of ≈2 Ω sq−1, resistance increase of only 5% upon encapsulation, and vastly improved ...
Fatemeh Bayat, Mohammad Nazeri, Gerd Grau, Simone Pisana   +3 more
wiley   +1 more source

Development of SiC Nanocomposites Using Direct Ink Writing Process

Advanced Engineering Materials, EarlyView.
Herein, feedstock inks containing polycarbosilane and various concentrations of SiC nanoparticles (SiCnp) are investigated for fabricating ceramic matrix composites using a DIW 3D printing process. Characterization results from physical measurement, microstructure analysis, and thermal and flexural testing suggested that high‐performance CMC samples ...
Jinchen Han, Israa Eltahir Ali Elfaki, Luke Weston, Chenggang Chen, Donald A. Klosterman, Li Cao   +5 more
wiley   +1 more source

The influence of changes in water content on the electrical resistivity of a natural unsaturated loess [PDF]

, 2012
Non-destructive methods of measuring water content in soils have been extensively developed in the last decades, especially in soil science. Among these methods, the measurements based on the electrical resistivity are simple and reliable thanks to the ...
Cui, Yu Jun, Delage, Pierre, Munoz-Castelblanco, José, Pereira, Jean-Michel   +3 more
core   +3 more sources

Production of Metallic Foam Precursors Using Current‐Activated Pressure‐Assisted Densification

Advanced Engineering Materials, EarlyView.
A powder compaction metallurgical method, known as current‐activated pressure‐assisted densification, is applied to enhance the compaction of metal foam precursors. This method improves precursor quality by achieving higher density, lower electrical resistivity, and more uniform pore nucleation in the resulting foams, reducing energy consumption and ...
Tillmann Robert Neu, Paul Hans Kamm, Francisco García‐Moreno   +2 more
wiley   +1 more source

The Effect of Moisture Content on the Electrical Properties of Graphene Oxide/Cementitious Composites

Applied Sciences
Due to its ability to improve mechanical properties when incorporated into cement, graphene oxide (GO) has received extensive attention from scholars.
Zhengxian Liang, Haiting Xia, Feng Yan, Kaomin Zhang, Rongxin Guo   +4 more
doaj   +1 more source

Preparation and characterization of Ni-Cu composite nanoparticles for conductive paints

Science and Engineering of Composite Materials, 2019
Ni and Cu are the two most promising alternatives to noble metals used in electrical conductive materials. However, Cu is susceptible to oxidation, while Ni exhibits poorer electrical conductivity.
Bai Liuyang
doaj   +1 more source

Efficient and Scalable Radiative Cooling for Photovoltaics Using Solution‐Processable and Solar‐Transparent Mesoporous Nanoparticles

Advanced Functional Materials, EarlyView.
Graded refractive index (GRI) structures are prepared from the layer‐by‐layer spray coating of the mesoporous SiO2 nanoparticles, showing high solar transparency and thermal emissivity. Under outdoor conditions, after 50 days, the GRI‐coated photovoltaics show on average 6.65 ± 1.48 °C lower than that of the non‐coated references, maintaining 80.9 ± 8 ...
Heesuk Jung, Sung Yoon Min, Byungsoo Kang, Yongseok Yoo, Jihun Jang, Yeoun‐Woo Jang, Hyojeong Choi, Hyeong Won Lee, Swarup Biswas, Yongju Lee, Mansoo Choi, Phillip Lee, Min Seok Jang, Hyeok Kim, Shu Yang   +14 more
wiley   +1 more source

Mechanically Adaptable High‐Performance p(SBMA‐MMA) Copolymer Hydrogel with Iron (II/III) Perchlorate for Wearable Thermocell Applications

Advanced Functional Materials, Volume 35, Issue 12, March 18, 2025.
A high‐performance n‐type element for quasi‐solid‐state thermocells has been introduced, outperforming conventional p‐type elements and showcasing the potential to harness body heat as an energy source or power embedded sensors. This advance significantly contributes to waste thermal energy harvesting and wearable technology, paving the way for self ...
Gilyong Shin, Jae Yoon Baek, Ju Hyeon Kim, Ju Hwan Lee, Hyeong Jun Kim, Byeong Jun So, Yuseung Choi, Sungryul Yun, Taewoo Kim, Jei Gyeong Jeon, Tae June Kang   +10 more
wiley   +1 more source

Effects of latex type and processed-mica waste loading on the structural and thermo-physical properties of natural rubber latex foam composites

International Journal of Lightweight Materials and Manufacture
Mica waste, a type of commercial waste produced in bulk quantities by the mica mining industry, was processed and added to Natural Rubber Latex Foams (NRLF) made of centrifuged and creamed latex.
Vimukthi Dananjaya, Yashoda Somarathna, Susantha Siriwardena, Narayana Sirimuthu, Laleen Karunanayake, Chamil Abeykoon   +5 more
doaj   +1 more source

Stabilized Intermediate Phase Via Pseudo‐Halide Anions Toward Highly Efficient and Light‐Soaking Stable Perovskite Solar Cells

Advanced Functional Materials, Volume 35, Issue 12, March 18, 2025.
The formate pseudo‐halide anion is strategically introduced at the buried interface to stabilize the intermediate phases formed during perovskite crystallization. The controlled crystallization enhances crystallinity and alleviates tensile strain, eliminating residual PbI2 near the buried interface.
Jongdeuk Seo, Yun Seop Shin, Dong Gyu Lee, Jaehwi Lee, Jina Roe, Jung Geon Son, Woojin Lee, Yeonjeong Lee, Dongmin Lee, Ji Won Song, Tae Kyung Lee, Dong Suk Kim, Jin Young Kim   +12 more
wiley   +1 more source