Results 101 to 110 of about 10,464 (286)
Comparison of Electrochemical Noise (EN) Signal And Corrosion Products Signal Image of Ti-6Al-4V
International Journal of Electrochemical Science, 2012 Electrochemical noise (EN) measurements and their corrosion products were observed by Scanning Electron Microscopy (SEM). Digital image process allows changing the image result of corrosion products in an equivalent signal.
C.G. Nava-Dino +7 more
doaj +1 more source
Advanced Materials Technologies, EarlyView.Milled polycrystalline NMC811 cathode (MPC NMC) with smaller secondary particle and higher surface area had 1) greater cathode tortuosity, 2) reduced surface Ni on the cycled MPC cathodes consistent with surface reconstruction, and 3) increased Ni deposition from cathode‐anode crosstalk, manifesting in lower functional capacity and higher impedance ...
Edelmy J. Marin Bernardez +22 more
wiley +1 more source
Electrochemical milling removes burrs and solder from tubing ends
, 1966 Electrochemical milling removes burrs and solder from the cut ends of stainless steel capillary tubing.
Hinshaw, J. O.
core
Experimental Investigation on Electrochemical Discharge Milling of Micro Structures on Quartz Glass
, 2019 Background: The fabrication of micro-groove and microstructures in non-conductive hard and brittle materials is always difficult. The electrochemical discharge milling process is a good selection for the fabrication of micro-grooves and microstructures.
Songsong Li, Zhiyuan Wei, Yong Liu
core +1 more source
Advanced Materials Technologies, EarlyView.ABSTRACT Molybdenum disulfide (MoS2) has attracted attention as a promising material due to the growing demand for environmentally friendly, cost‐effective, and efficient water treatment techniques. With its physicochemical characteristics, this stratified bidimensional material allows it to be highly effective in adsorption and catalytic performance ...
Pariksha Bishnoi +4 more
wiley +1 more source
Simulation and Experimental Investigation of Electrochemical Mill-grinding of GH4169 Alloy
International Journal of Electrochemical Science, 2018 Electrochemical mill-grinding (ECMG) is a new method of compound machining inspired by numerical-control milling. A simple rodlike grinding wheel that rotates at high speed is used as the cathode and processes the workpiece along a set trajectory ...
Hansong Li +3 more
doaj +1 more source
Advanced Materials Technologies, EarlyView.We introduce an additively manufactured bioreactor with a perfusion flow system and integrated temperature and pH sensors for skeletal muscle tissue biofabrication. The bioreactor's performance was evaluated by assessing the viability, spreading of the myoblast cells in a printed scaffold, and contraction of the isolated murine musculi interossei ...
Lys Sprenger +9 more
wiley +1 more source
International Journal of Electrochemical Science, 2017 Composite material LiNi1/3Co1/3Mn1/3O2 cathode material for lithium-ion battery was obtained with lithium carbonate, nickel (II) oxide, cobalt (II, III) oxide and manganese dioxide as raw materials by high temperature ball milling method.
Ming Tian +3 more
doaj +1 more source
Effects of Ball Milling on the Electrochemical Capacity and Interfacial Stability of Li2MnO3 Cathode Materials [PDF]
The cycling mechanism of Li2MnO3 cathode materials synthesized by conventional solid-state methods at high temperatures (800-900 °C) has been intensively investigated.
McCloskey, Bryan D +7 more
core +1 more source
Shaping Carbon Nitrides for Advanced Macrostructures
Advanced Materials Technologies, EarlyView.This review examines how carbon nitride can be shaped through a range of printing and interfacial assembly methods. By bringing together additive manufacturing and liquid–liquid structuring concepts, carbon nitride is moving beyond its traditional powder‐based photocatalyst form toward digitally designed robust macroscale architectures with high design
Simona Baluchová, Baris Kumru
wiley +1 more source