Results 21 to 30 of about 9,082 (250)
Polyol mediated synthesis and electrochemical performance of nanostructured LiMn2O4 cathodes
International Journal of Electrochemical Science, 2016 Nanoparticulate single phase LiMn2O4 spinel was prepared via polyol method and applied as a cathode in a lithium ion battery. The effects of calcination temperature (250 °C – 800 °C) as well as of post-synthetic treatment by ball milling on the ...
Shuo Yang +3 more
doaj +1 more source
Electrochemical Noise Response of Cr2Nb Powders Applying Mechanical Alloying
Crystals, 2022 Cr2Nb alloys are potential candidates for high-temperature structural materials. The influence of different mechanical alloying parameters (milling time) and sintering processes were studied. After mechanical alloying and observation by scanning electron
Claudia Georgina Nava-Dino +6 more
doaj +1 more source
Investigation on Hybrid Mechano-electrochemical Milling of Ti6Al4V
Procedia CIRP, 2018 Abstract To satisfy the increasing demand for processing high-performance materials in industry, a new hybrid process, Mechano-Electrochemical Milling (MECM), is developed in this research. This hybrid machining process combines the effect of both the conventional milling process and the Electrochemical Machining process (ECM).
Van Camp, Dries +4 more
openaire +2 more sources
Carbon Trends, 2021 Controlled structural and chemical defects were induced on to graphene oxide (GO) by mechanical milling of the precursor graphitic sheets for different times followed by their chemical oxidation. Raman, XRD, FTIR, XPS and AFM measurements was carried out
R. Ashwini +4 more
doaj +1 more source
Micro EDM Milling with Automated Electrochemical Fabrication of the Cylindrical Microtool [PDF]
Proceedings of the 7th International Conference on Multi-Material Micro Manufacture, 2010 Micro electrical discharge machining in the milling configuration (µEDM milling) allows machining of complex microparts in a flexible way by controlling the erosion process along the 3D path of a thin cylindrical microtool. This technique is attracting growing interest for the processing of mesoscopic and/or high aspect ratio parts. A bottleneck in the
Layouni, Y +6 more
openaire +2 more sources
Micromachines, 2019 As one of the most promising micro-machining methods, electrochemical micro-machining is widely used in the field of metal micro-structures. The electrochemical micro-milling on Nickel-base superalloy by using high-speed spiral electrode was studied in ...
Yong Liu +3 more
doaj +1 more source
Electrochemical Micromachining of Square Holes in Stainless Steel in H2SO4
International Journal of Electrochemical Science, 2019 A method for fabricating micro square holes with small corner radius is proposed, which could find applications in the aerospace and aviation industries.
Gu Mingcheng +2 more
doaj +1 more source
Advances in Materials Science and Engineering, 2018 Aiming at the preparation of high electrochemical performance LiNi1/3Co1/3Mn1/3O2 cathode material for lithium-ion battery, LiNi1/3Co1/3Mn1/3O2 was prepared with lithium carbonate, nickel (II) oxide, cobalt (II, III) oxide, and manganese dioxide as raw ...
Ming Tian +3 more
doaj +1 more source
Effects of Microelectrochemical Milling Parameters on the Microstructures of Co40CrNiMo
International Journal of Electrochemical Science, 2020 Microparts made of highly elastic alloys are increasingly applied in many industries, including aeronautics and astronautics, precision devices and so on. However, it is difficult to machine these parts with traditional machining technologies.
Changfu Zhang +4 more
doaj +1 more source
Research on Using Mechanical and Chemical Methods to Synthesize Lithium Battery Electrode Materials
Chemical Engineering Transactions, 2017 In order to study the influence of mechanical and chemical treatment on the performance of SiO2 negative electrode materials, this paper prepares SiO2 negative electrode materials by mechanical ball milling.
Huomei Zhu +3 more
doaj +1 more source