Results 101 to 110 of about 271,766 (267)
In Situ Study of Resistive Switching in a Nitride‐Based Memristive Device
In situ TEM biasing experiment demonstrates the volatile I‐V characteristic of MIM lamella device. In situ STEM‐EELS Ti L2/L3 ratio maps provide direct evidence of the oxygen vacancies migrations under positive/negative electrical bias, which is critical for revealing the RS mechanism for the MIM lamella device.
Di Zhang +19 more
wiley +1 more source
Precursor‐ and solvent‐mediated synthesis yields four Cu3(HHTP)2 morphologies with distinct physicochemical, sorption, and sensing properties toward SO2. Uptake capacities correlate with BET surface area, while sensing performance scales with particle aspect ratio.
Patrick Damacet +5 more
wiley +1 more source
The combination of formamidinium thiocyanate and 1,3‐propane diammonium iodide for bulk and top‐surface passivation, and a ternary fullerene blend to improve energy band alignment, suppresses energy losses in wide‐bandgap FAPbBr3 perovskite solar cells.
Laura Bellini +9 more
wiley +1 more source
This work presents a continuous linear gradient catalyst layer design, a general strategy for improving membrane electrode assemblies across electrochemical devices. Fabricated via a dual‐nozzle spray coating method, the architecture controls the Pt/carbon ratio, ionomer content and ionomer type across the catalyst layer, enhancing proton conduction ...
Shangwei Zhou +15 more
wiley +1 more source
Electroactive Liquid Crystal Elastomers as Soft Actuators
Electroactive liquid crystal elastomers (eLCEs) can be actuated via electromechanical, electrochemical, or electrothermal effects. a) Electromechanical effects include Maxwell stress, electrostriction, and the electroclinic effect. b) Electrochemical effects arise from electrode redox reactions.
Yakui Deng, Min‐Hui Li
wiley +1 more source
Alumina (aluminium oxide or Al2O3) is one of the well-known ceramic materials. This material is widely used as abrasives, in the production of refractory products and glass, advanced ceramics, medical applications, and military and electronics applications. It is also used as a catalyst and/or catalyst support for various catalytic reactions.
openaire +1 more source
An All‐Optical Driven Bio‐Photovoltaic Interface for Active Control of Live Cells
Bio‐photovoltaic Interface (BIO‐PV‐I) for live cell manipulation is presented. BIO‐PV‐I can be activated non‐invasively and remotely to control the spatial motility, adhesion, and morphology of cells adhering to it. BIO‐PV‐I uses a patterned light‐induced electric potential in iron‐doped lithium niobate crystals whose light‐driven and reversible nature,
Lisa Miccio +8 more
wiley +1 more source
A roll‐to‐roll exfoliation method is demonstrated that preserves the crystallographic alignment of anisotropic 2D materials over large areas, enabling scalable fabrication of directional electronic and optoelectronic devices. Abstract Anisotropic 2D materials such as black phosphorus (BP), GeS or CrSBr, exhibit direction‐dependent optical and ...
Esteban Zamora‐Amo +14 more
wiley +1 more source
Here, we present a high‐density PEDOT eutectogel electrode array for enhanced body surface gastric mapping. Silver electrodes are blade‐coated onto flexible substrates, followed by electrogelation of PEDOT:PSS and the deposition of a PEDOT:LS eutectogel.
Christopher Slaughter +8 more
wiley +1 more source
Na‐ion batteries ‐ Impact of doping on the oxygen redox: The sloping potential of NaMg0.1Ni0.4Mn0.5O2 above 4.0 V is caused by a new redox center (arising from the ‘O bound to Mg’), having a higher potential but being more irreversible compared to the ‘O bound to Ni’.
Yongchun Li +12 more
wiley +1 more source

