Results 131 to 140 of about 23,925 (258)

Controlled Synthesis of Tri‐ and Multi‐Doped Graphene

Advanced Materials Interfaces, EarlyView.
This review systematically evaluates synthesis routes for tri‐ and multi‐doped graphene, from hydrothermal and pyrolysis methods to flash Joule heating, critically assessing how each governs dopant incorporation, bonding configuration, and resulting electronic properties.
Maria Hasan, Alicja Bachmatiuk, Gražyna Simha Martynková, Karla Čech Barabaszová, Mark Hermann Rümmeli   +4 more
wiley   +1 more source

Texturing and Phase Evolution in Ti-6Al-4V: Effect of Electron Beam Melting Process, Powder Re-Using, and HIP Treatment. [PDF]

Materials (Basel), 2021
Popov VV, Lobanov ML, Stepanov SI, Qi Y, Muller-Kamskii G, Popova EN, Katz-Demyanetz A, Popov AA.   +7 more
europepmc   +1 more source

Large‐Scale and Cost‐Effective Fabrication of Ultra‐Thin, Biodegradable Microelectrode Arrays and Pressure Sensors Using Laser Micromachining

Advanced Materials Technologies, EarlyView.
A mask‐free and cost‐effective UV‐pico‐second laser‐based microfabrication method is proposed to fabricate large‐area biodegradable microelectrode arrays and pressure sensors. These devices demonstrate low impedance, good conformability, excellent biocompatibility, and rapid degradation, providing a new route for next‐generation transient electronics ...
Bhavani Prasad Yalagala, Asfand Tanwear, María Cerezo‐Sánchez, Hossein Parvizi, Morteza Amjadi, Hadi Heidari   +5 more
wiley   +1 more source

Different Approaches for Manufacturing Ti-6Al-4V Alloy with Triply Periodic Minimal Surface Sheet-Based Structures by Electron Beam Melting. [PDF]

Materials (Basel), 2021
Khrapov D, Kozadayeva M, Manabaev K, Panin A, Sjöström W, Koptyug A, Mishurova T, Evsevleev S, Meinel D, Bruno G, Cheneler D, Surmenev R, Surmeneva M.   +12 more
europepmc   +1 more source

The Evolution of Aerosol Jet Printing, A Review: Enhancing Material Versatility and Improvements for Next‐Generation Applications

Advanced Materials Technologies, EarlyView.
Aerosol Jet Printing (AJP) has emerged as a versatile additive manufacturing technique for high‐resolution, conformal, and multi‐material printing. This review highlights advances in printable materials, substrate compatibility, post‐processing, characterization, and process innovations, while critically discussing current challenges and future ...
Chandrachur Chatterjee, Rocco Lupoi, Michael J. Gibbons   +2 more
wiley   +1 more source

Fabrication of Fibers With Complex Features Using Thermal Drawing of 3D‐Printed Preforms

Advanced Materials Technologies, EarlyView.
3D printing enables rapid fabrication of macroscale polymer preforms with complex geometries. Thermal drawing then scales these structures into long fibers while preserving micron‐scale cross‐sectional features. This workflow provides a fast, low‐cost route to functional fibers with tailored geometries and material combinations for catheter, robotic ...
Ali Anil Demircali, Jinshi Zhao, Ayhan Aktas, Mohamed E. M. K. Abdelaziz, Burak Temelkuran   +4 more
wiley   +1 more source

Microstructural and Mechanical Evaluation of a Cr-Mo-V Cold-Work Tool Steel Produced via Electron Beam Melting (EBM). [PDF]

Materials (Basel), 2021
Botero CA, Şelte A, Ramsperger M, Maistro G, Koptyug A, Bäckström M, Sjöström W, Rännar LE.   +7 more
europepmc   +1 more source

3D‐Printed Dual‐Doped Ag2Se‐Based Thermoelectric Films With Enhanced Thermal Stability

Advanced Materials Technologies, EarlyView.
Sb–Se dual doping enhances the thermal stability of Ag2Se‐based thermoelectric systems. The compositionally tuned nano‐ink is printed into flexible films by direct ink writing (DIW), retaining improved thermoelectric properties after annealing up to 400°C.
Ahasun Habib Hridoy, Nishat Paul, Naimul Arefin, Axel Lopez, Peiran Wei, Brandon Dumars, Yan Chen, Mortaza Saeidi, Minxiang Zeng   +8 more
wiley   +1 more source

In Situ Two‐Dimensional Residual Stress Characterization of Thin Films

Advanced Materials Technologies, EarlyView.
An integrated in situ curvature metrology platform combining speckle‐based curvature optical metrology (SCOM) with multi‐beam optical sensors (MOS) enables spatially resolved two‐dimensional curvature mapping of thick sputtered coatings. The SCOM technique provides excellent agreement with MOS while providing an extended measurable curvature range ...
Wai Jue Tan, Wadwan Singhapong, Arindam Majhi, Chris Bowen, Alexander J.G. Lunt, Hongchang Wang, Kawal Sawhney   +6 more
wiley   +1 more source

The Tensile Properties of Electron Beam Melted Molybdenum Wires (Electron Beam Electron Melting of Refractory Metals (III))

Journal of the Japan Institute of Metals, 1965
Tetsuya Takaai, Mitsuru Ishii
openaire   +2 more sources