Results 71 to 80 of about 154,985 (209)

Effects of Mg on Microstructure and Solidification of a Hypereutectic Zn–8 wt.%Al Alloy

Advanced Engineering Materials, EarlyView.
An appreciable set of results involving thermal data, microstructure, chemical composition, and microstructural growth laws is reported for ZnAlMg alloys. Such results demonstrate that ZnAlMg alloys have high potential for applications in automotive self‐lubricating components, batteries, and electrical systems.
Raí B. de Sousa, Jeverton L. Paixão, Daylla S. Silva, Bruno S. Sobral, Mucio D. de Medeiros, José E. Spinelli, Bismarck L. Silva   +6 more
wiley   +1 more source

Electron-irradiation induced unconventional phase transition of β-Ga2O3 epitaxial single-crystal thin film observed by in-situ TEM

Journal of Materials Research and Technology
In this work, the phase transition process of β-Ga2O3 thin films under heating and (or) electron irradiation condition was investigated by in-situ transmission electron microscopy. It is found that only under the high temperature, β-Ga2O3 did not undergo
Qing Zhu, Jiatong Fan, Yuxiang Wei, Zhan Wang, Jiejie Zhu, Jing Sun, Zhenni Wang, Xichen Wang, Ling Yang, Shaojie Song, Yimin Lei, Xiaohua Ma   +11 more
doaj   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Electron-induced deposition using Fe(CO)4MA and Fe(CO)5 – effect of MA ligand and process conditions

Beilstein Journal of Nanotechnology
The electron-induced decomposition of Fe(CO)4MA (MA = methyl acrylate), which is a potential new precursor for focused electron beam-induced deposition (FEBID), was investigated by surface science experiments under UHV conditions.
Hannah Boeckers, Atul Chaudhary, Petra Martinović, Amy V. Walker, Lisa McElwee-White, Petra Swiderek   +5 more
doaj   +1 more source

Electron microscopy data on irradiation effects in glassy carbon, nuclear graphite, pyrolytic carbon, and carbon fibersMendeley Data

Data in Brief
Glassy carbon, a monoatomic allotrope of carbon, is a candidate material for components in fission nuclear power systems due to its radiation tolerance.
J. David Arregui-Mena, Takaaki Koyanagi, David A. Cullen, Michael J. Zachman, Yan-Ru Lin, Kyle Everett, Sabrina Gonzalez-Calzada, Phillip D. Edmondson, Tyler J. Gerczak, Yutai Katoh, Nidia C. Gallego   +10 more
doaj   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

Effect of electron beam irradiation on the structure of Ta-doped lithium-lanthanum-zirconium-oxygen (Li6.5La3Zr1.5Ta0.5O12) solid electrolytes

Fushe yanjiu yu fushe gongyi xuebao
Ta-doped lithium-lanthanum-zirconium-oxygen (Li6.5La3Zr1.5Ta0.5O12, LLZTO) solid electrolytes with a high ionic conductivity at room temperature were prepared by the solid-phase reaction method, and the effects of irradiated electron beams on their ...
WANG Daoxi, SHI Haiting, LIU Shengkai, SHAO Ruiqi, WANG Shuo, ZENG Ming, XU Zhiwei   +6 more
doaj   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

Development of a method for measuring low energy electron beam irradiation parameters by calorimetry and step stacking

Fushe yanjiu yu fushe gongyi xuebao
Electron beam irradiation processing has become an important component of the nuclear technology industry, with low-energy electron beam increasingly being applied in processes such as coating curing, wastewater treatment, and food preservation. Accurate
LUO Rui, ZHANG Yuhe, MAO Naqing
doaj   +1 more source