Results 121 to 130 of about 440,979 (305)
3D‐Printed Sulfur‐Derived Polymers With Controlled Architectures for Lithium‐Sulfur Batteries
Advanced Functional Materials, EarlyView.Rheology‐guided formulation design for direct ink writing enables the fabrication of 3D sulfur copolymer cathodes with controlled architectures for lithium‐sulfur batteries. The printed electrodes exhibit multiscale porosity and high sulfur utilization, delivering enhanced electrochemical performance compared to conventional cast electrodes.
Bin Ling +7 more
wiley +1 more source
A Portable Cooling System Based on Compression Refrigeration
Zhileng xuebao, 2017 A portable cooling system for military electronic is developed to solve cooling problems under high temperature circumstance by integrating the micro efficient refrigeration components.
doaj
Advanced Functional Materials, EarlyView.Herein presented supraparticles combine the nanoparticulate photocatalyst graphitic carbon nitride with the enzyme horseradish peroxidase, which is immobilized on silica nanoparticles. In an optimized compatibility range, both catalysts operate effectively within the hybrid supraparticles and catalyze a cascade reaction consisting of the photocatalytic
Bettina Herbig +11 more
wiley +1 more source
Hot electron cooling by acoustic phonons in graphene
, 2012 We have investigated the energy loss of hot electrons in metallic graphene by means of GHz noise thermometry at liquid helium temperature. We observe the electronic temperature T / V at low bias in agreement with the heat diffusion to the leads described
A. C. Betz +11 more
core +1 more source
Advanced Functional Materials, EarlyView.A food‐grade cooling composite made from starch and recycled eggshell powder offers a scalable, ultra‐low‐cost solution for passive daytime radiative cooling. Easily prepared using basic kitchen tools, this material empowers communities, even in areas with limited infrastructure, to stay cooler during worsening summer heat waves.
Qimeng Song +3 more
wiley +1 more source
Mixed-Valence-Driven Heavy-Fermion Behavior and Superconductivity in KNi$_2$Se$_2$
, 2012 Based on specific heat and magnetoresistance measurements, we report that a "heavy" electronic state exists below $T \approx$ 20 K in KNi$_2$Se$_2$, with an increased carrier mobility and enhanced effective electronic band mass, $m$* = 6$m_b$ to 18$m_b$.
Armitage, N. P. +9 more
core +1 more source
MOFs and COFs in Electronics: Bridging the Gap between Intrinsic Properties and Measured Performance
Advanced Functional Materials, EarlyView.Metal‐organic frameworks (MOFs) and covalent organic frameworks (COFs) hold promise for advanced electronics. However, discrepancies in reported electrical conductivities highlight the importance of measurement methodologies. This review explores intrinsic charge transport mechanisms and extrinsic factors influencing performance, and critically ...
Jonas F. Pöhls, R. Thomas Weitz
wiley +1 more source
Electronic calorimetric computer [PDF]
, 1968 Electronic calorimetric computer calculates nuclear reactor thermal power output to a nominal accuracy of 1 percent. Heat balance is determined by an electronic approach.
Heckelman, J. D.
core +1 more source
, 2010 In a nanoscale molecular junction at finite bias voltage,the intra-molecular distribution of vibrational energy can strongly deviate from the thermal equilibrium distribution and specific vibrational modes can be selectively excited in a controllable way,
Brumer P. W. +4 more
core +1 more source
In Situ Study of Resistive Switching in a Nitride‐Based Memristive Device
Advanced Functional Materials, EarlyView.In situ TEM biasing experiment demonstrates the volatile I‐V characteristic of MIM lamella device. In situ STEM‐EELS Ti L2/L3 ratio maps provide direct evidence of the oxygen vacancies migrations under positive/negative electrical bias, which is critical for revealing the RS mechanism for the MIM lamella device.
Di Zhang +19 more
wiley +1 more source